参数资料
| 型号： | DS3105LN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 42/124页 |
| 文件大小： | 0K |
| 描述： | IC TIMING LINE CARD 64-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 160 |
| 类型： | 定时卡 IC，多路复用器 |
| PLL： | 是 |
| 主要目的： | 以太网，SONET/SDH，Stratum，电信 |
| 输入： | CMOS，LVDS，LVPECL，TTL |
| 输出： | CMOS，LVDS，LVPECL，TTL |
| 电路数： | 1 |
| 比率 - 输入:输出： | 5:2 |
| 差分 - 输入:输出： | 无/是 |
| 频率 - 最大： | 312.5MHz |
| 电源电压： | 1.62 V ~ 1.98 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页当前第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页
DS3105
24
no input is forced) is listed as the second-highest priority (PTAB2:REF2) and the normal second-highest priority
input is listed as the third-highest priority (PTAB2:REF3).
When the T4 DPLL is used to measure the phase difference between the T0 DPLL selected reference and another
reference input by setting the T0CR1:T4MT0 bit, the T4FORCE field in the MCR4 register can be used to select the
other reference input.
7.6.4 Ultra-Fast Reference Switching
By default, disqualification of the selected reference and switchover to another reference occurs when the activity
monitor’s inactivity alarm threshold has been crossed, a process that takes on the order of hundreds of
milliseconds or seconds. For the T0 DPLL, an option for extremely fast disqualification and switchover is also
available. When ultra-fast switching is enabled (MCR10:UFSW = 1), if the fast activity monitor detects
approximately two missing clock cycles, it declares the reference failed by forcing the leaky bucket accumulator to
its upper threshold (see Section 7.5.2) and initiates reference switching. This is in addition to setting the SRFAIL bit
in MSR2 and optionally generating an interrupt request, as described in Section 7.5.3. When ultra-fast switching
occurs, the T0 DPLL transitions to the prelocked 2 state, which allows switching to occur faster by bypassing the
loss-of-lock state. The device should be in nonrevertive mode when ultra-fast switching is enabled. If the device is
in revertive mode, ultra-fast switching could cause excessive reference switching when the highest priority input is
intermittent.
7.6.5 External Reference Switching Mode
In this mode the SRCSW input pin controls reference switching between two clock inputs. This mode is enabled by
setting the EXTSW bit to 1 in the MCR10 register. In this mode, if the SRCSW pin is high, the T0 DPLL is forced to
lock to input IC3 (if the priority of IC3 is nonzero in IPR2) or IC5 (if the priority of IC3 is zero) whether or not the
selected input has a valid reference signal. If the SRCSW pin is low, the T0 DPLL is forced to lock to input IC4 (if
the priority of IC4 is nonzero in IPR2) or IC6 (if the priority of IC4 is zero) whether or not the selected input has a
valid reference signal. During reset the default value of the EXTSW bit is latched from the SRCSW pin. If external
reference switching mode is enabled during reset, the default frequency tolerance (DLIMIT registers) is configured
to
±80ppm rather than the normal default of ±9.2ppm.
In external reference switching mode the device is simply a clock switch, and the T0 DPLL is forced to lock onto the
selected reference whether or not it is valid. Unlike forced reference selection (Section 7.6.3) this mode controls the
PTAB1:SELREF field directly and is, therefore, not affected by the state of the MCR3:REVERT bit. During external
reference switching mode, only PTAB1:SELREF is affected; the REF1, REF2, and REF3 fields in the PTAB
registers continue to indicate the highest, second-highest, and third-highest priority valid inputs chosen by the
automatic selection logic. External reference switching mode only affects the T0 DPLL.
7.6.6 Output Clock Phase Continuity During Reference Switching
If phase build-out is enabled (PBOEN = 1 in MCR10) or the DPLL frequency limit (DLIMIT) is set to less than
±30ppm, the device always complies with the GR-1244-CORE requirement that the rate of phase change must be
less than 81ns per 1.326ms during reference switching.
相关PDF资料 |
PDF描述 |
|---|---|
| DS3106LN+ | IC TIMING LINE CARD 64-LQFP |
| DS3231MZ+ | IC RTC I2C 8SOIC |
| DS3231SN#T&R | IC RTC W/TCXO 16-SOIC |
| DS3232MZ+ | IC RTC W/SRAM I2C 8SOIC |
| DS3232SN#T&R | IC RTC W/TCXO 20-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3105LN+ | 功能描述:计时器和支持产品 Line Card Timing IC RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| DS3106 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Line Card Timing IC |
| DS3106A10SL3S(621) | 制造商:Amphenol Corporation 功能描述: |
| DS3106A14S2S | 制造商:Amphenol Corporation 功能描述: |
| DS3106A14S2S(621) | 制造商:Amphenol Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。