参数资料
型号: FUSION878A
厂商: CONEXANT SYSTEMS
元件分类: 颜色信号转换
英文描述: COLOR SIGNAL DECODER, PQFP128
封装: PLASTIC, QFP-128
文件页数: 11/180页
文件大小: 2067K
代理商: FUSION878A
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页
3.0 Electrical Interfaces
Fusion 878A
3.5 I2C Serial EEPROM Interface
PCI Video Decoder
3-24
Conexant
100600B
3.5.2 Subsystem Vendor ID
PCI Configuration Header Location 0x2C specifies the subsystem vendor ID and
the subsystem ID. If an external EEPROM is present, the subsystem vendor ID
and subsystem ID and vital product data are uploaded. If an external EEPROM is
not present, the 32 bits of the header register default to 0x0000, and the register
can be programmed using BIOS.
This chapter defines the subsystem vendor ID configuration with and without
an EEPROM present. For more details on the Function 1 definition, refer to
Section 6.1. The Function 0 subsystem vendor ID registers are defined starting on
0x00—Vendor and Device ID Register, and the Function 1 subsystem vendor ID
registers are defined starting on 0x00—Vendor and Device ID Register.
3.5.2.1 EEPROM Upload
at PCI Reset
The 32-bit subsystem IDs are read from the EEPROM by taking control of the
I2C circuit just after PCI reset and performing a 4-byte sequential read access
transaction in the 100 kHz mode, starting at physical address 0xFC. The full read
sequence is detailed in Table 3-7.
If at any time the slave device issues a NACK (because the device is not
present), the sequence is aborted, and the subsystem vendor IDs read
0x00000000. Normally it will take ~660 s to read this DWORD into the PCI
configuration register. If this register is accessed before it is updated, the PCI
target will issue a RETRY.
3.5.2.2 Register Load
from BIOS
The Subsystem IDs register is read-only. However, by enabling SVIDS_EN in the
user-defined PCI configuration control register, the Subsystem Vendor IDs can be
written. Then SVIDS_EN should be disabled. This value needs to be programmed
before OS boots and has access during configuration. This must occur via support
from the BIOS versus the IC driver. If this feature can be supported by software
(and Vital Product Data is not supported), then the external EEPROM is not
required.
Table 3-7. EEPROM Upload Sequence
Master
Slave
Master
Comment
Control
Data
Control
START
0xA0
ACK
Write control byte with slave chip address
0xFC
ACK
Data bytes base address
START
0xA1
ACK
Read control byte with slave chip address
——
0x
ACK
Subsystem ID [15:8] at 0xFC
——
0x
ACK
Subsystem ID [7:0] at 0xFD
——
0x
ACK
Subsystem Vendor ID [15:8] at 0xFE
——
0x
NACK,STOP
Subsystem Vendor ID [7:0] at 0xFF
相关PDF资料
PDF描述
FVXO-HC53BR-FREQ VCXO, CLOCK, 0.75 MHz - 250 MHz, HCMOS OUTPUT
FVXO-HC72BR-FREQ VCXO, CLOCK, 0.75 MHz - 180 MHz, HCMOS OUTPUT
FVXO-HC73B-FREQ VCXO, CLOCK, 0.75 MHz - 250 MHz, HCMOS OUTPUT
FVXO-LC52BR-FREQ VCXO, CLOCK, 0.75 MHz - 1000 MHz, LVDS OUTPUT
FVXO-LC72BR-FREQ VCXO, CLOCK, 0.75 MHz - 1000 MHz, LVDS OUTPUT
相关代理商/技术参数
参数描述
FUSZ03 制造商:Honeywell Sensing and Control 功能描述:
FUTURE 1AA PLUS 制造商:Ansmann 功能描述: 制造商:ANSMANN AG 功能描述:
FUTURE 2AA PLUS 制造商:Ansmann 功能描述: 制造商:ANSMANN AG 功能描述:
FUTURE 2C PLUS 制造商:Ansmann 功能描述: 制造商:ANSMANN AG 功能描述:
FUTURE 3D PLUS 制造商:Ansmann 功能描述: 制造商:ANSMANN AG 功能描述: