参数资料
型号: MCR705JP7CDWE
厂商: Freescale Semiconductor
文件页数: 126/164页
文件大小: 0K
描述: MCU 8BIT 224B RAM 28-SOIC
标准包装: 26
系列: HC05
核心处理器: HC05
芯体尺寸: 8-位
速度: 2.1MHz
连通性: SIO
外围设备: POR,温度传感器,WDT
输入/输出数: 22
程序存储器容量: 6KB(6K x 8)
程序存储器类型: OTP
RAM 容量: 224 x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 5.5 V
数据转换器: A/D 4x12b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 28-SOIC(0.295",7.50mm 宽)
包装: 管件
Parallel Input/Output
MC68HC705JJ7 MC68HC705JP7 Advance Information Data Sheet, Rev. 4.1
64
Freescale Semiconductor
7.3.8 PB6/SDI Logic
The PB6/SDI pin can be used as a simple I/O port pin or be controlled by the SIOP serial interface as
shown in Figure 7-11. The operations of PB6/SDI pin are summarized in Table 7-3.
Figure 7-11. PB6/SDI Pin I/O Circuit
When using the PB6/SDI pin, these interactions must be noted:
1.
If the SIOP function is required, then the SPE bit in the SCR must be set. This causes the PB6/SDI
pin buffer to be disabled to allow the PB6/SDI pin to act as an input that feeds the serial data input
(SDI) of the SIOP. The pulldown device is disabled in this case.
2.
If the SIOP function is in control of the PB6/SDI pin, the DDRB6 and PB6 data register bits are still
accessible to the CPU and can be altered or read without affecting the SIOP functionality.
However, if the DDRB6 bit is cleared, reading the PB6 data register will return the current state of
the PB6/SDI pin.
3.
If the SIOP function is terminated by clearing the SPE bit in the SCR, then the last conditions stored
in the DDRB6, PDIB6, and PB6 register bits will then control the PB6/SDI pin.
4.
If the PB6/SDI pin is to be a digital input, then both the SPE bit in the SCR and the DDRB6 bit must
be cleared. Depending on the external application, the pulldown device may also be disabled by
setting the PDIB6 pulldown inhibit bit.
5.
If the PB6/SDI pin is to be a digital output, then the SPE bit in the SCR must be cleared and the
DDRB6 bit must be set. The pulldown device will be disabled in this case.
DATA DIRECTION
REGISTER B
BIT DDRB6
PORT B DATA
REGISTER
BIT PB6
PULLDOWN
REGISTER B
BIT PDIB6
R
PB6
READ $0005
WRITE $0001
READ $0001
WRITE $0011
PULLDOWN
DEVICE
RESET
INT
ERNAL
D
AT
A
B
U
S
WRITE $0005
SDI
SERIAL ENABLE (SPE)
SERIAL DATA IN (SDI)
SWPDI
MASK OPTION REG. ($1FF1)
相关PDF资料
PDF描述
MCHC705JP7CDWE IC MCU 8BIT 224 BYTES RAM 28SOIC
LF13WBJ-20P CONN JACK WATERPROOF 20POS MALE
MK20DX128VMP5 IC ARM CORTEX MCU 128KB 64BGA
MC908AP8ACBE IC MCU 8K FLASH 8MHZ 42-SDIP
VE-2N2-IY-F2 CONVERTER MOD DC/DC 15V 50W
相关代理商/技术参数
参数描述
MCR706A 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Silicon Controlled Rectifiers
MCR706AT4 功能描述:SCR 400V 4A RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流(在 VDRM IDRM 下):5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流(Ih 最大值):75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube
MCR706AT4G 功能描述:SCR THY 4A 400V SCR RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流(在 VDRM IDRM 下):5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流(Ih 最大值):75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube
MCR707A 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Silicon Controlled Rectifiers
MCR708A 功能描述:SCR 600V 4A RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流(在 VDRM IDRM 下):5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流(Ih 最大值):75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube