参数资料
型号: MCR705JP7CDWE
厂商: Freescale Semiconductor
文件页数: 34/164页
文件大小: 0K
描述: MCU 8BIT 224B RAM 28-SOIC
标准包装: 26
系列: HC05
核心处理器: HC05
芯体尺寸: 8-位
速度: 2.1MHz
连通性: SIO
外围设备: POR,温度传感器,WDT
输入/输出数: 22
程序存储器容量: 6KB(6K x 8)
程序存储器类型: OTP
RAM 容量: 224 x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 5.5 V
数据转换器: A/D 4x12b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 28-SOIC(0.295",7.50mm 宽)
包装: 管件
Instruction Types
MC68HC705JJ7 MC68HC705JP7 Advance Information Data Sheet, Rev. 4.1
Freescale Semiconductor
129
14.3.3 Jump/Branch Instructions
Jump instructions allow the CPU to interrupt the normal sequence of the program counter. The
unconditional jump instruction (JMP) and the jump-to-subroutine instruction (JSR) have no register
operand. Branch instructions allow the CPU to interrupt the normal sequence of the program counter
when a test condition is met. If the test condition is not met, the branch is not performed.
The BRCLR and BRSET instructions cause a branch based on the state of any readable bit in the first
256 memory locations. These 3-byte instructions use a combination of direct addressing and relative
addressing. The direct address of the byte to be tested is in the byte following the opcode. The third byte
is the signed offset byte. The CPU finds the effective branch destination by adding the third byte to the
program counter if the specified bit tests true. The bit to be tested and its condition (set or clear) is part of
the opcode. The span of branching is from –128 to +127 from the address of the next location after the
branch instruction. The CPU also transfers the tested bit to the carry/borrow bit of the condition code
register.
Table 14-3. Jump and Branch Instructions
Instruction
Mnemonic
Branch if Carry Bit Clear
BCC
Branch if Carry Bit Set
BCS
Branch if Equal
BEQ
Branch if Half-Carry Bit Clear
BHCC
Branch if Half-Carry Bit Set
BHCS
Branch if Higher
BHI
Branch if Higher or Same
BHS
Branch if IRQ/VPP Pin High
BIH
Branch if IRQ/VPP Pin Low
BIL
Branch if Lower
BLO
Branch if Lower or Same
BLS
Branch if Interrupt Mask Clear
BMC
Branch if Minus
BMI
Branch if Interrupt Mask Set
BMS
Branch if Not Equal
BNE
Branch if Plus
BPL
Branch Always
BRA
Branch if Bit Clear
BRCLR
Branch Never
BRN
Branch if Bit Set
BRSET
Branch to Subroutine
BSR
Unconditional Jump
JMP
Jump to Subroutine
JSR
相关PDF资料
PDF描述
MCHC705JP7CDWE IC MCU 8BIT 224 BYTES RAM 28SOIC
LF13WBJ-20P CONN JACK WATERPROOF 20POS MALE
MK20DX128VMP5 IC ARM CORTEX MCU 128KB 64BGA
MC908AP8ACBE IC MCU 8K FLASH 8MHZ 42-SDIP
VE-2N2-IY-F2 CONVERTER MOD DC/DC 15V 50W
相关代理商/技术参数
参数描述
MCR706A 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Silicon Controlled Rectifiers
MCR706AT4 功能描述:SCR 400V 4A RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流(在 VDRM IDRM 下):5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流(Ih 最大值):75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube
MCR706AT4G 功能描述:SCR THY 4A 400V SCR RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流(在 VDRM IDRM 下):5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流(Ih 最大值):75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube
MCR707A 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Silicon Controlled Rectifiers
MCR708A 功能描述:SCR 600V 4A RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流(在 VDRM IDRM 下):5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流(Ih 最大值):75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube