参数资料
| 型号： | AD9557BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/92页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK TRANSLATOR 40LFCSP |
| 产品变化通告： | Minor Mask Change 11/Apr/2012 |
| 标准包装： | 1 |
| 类型： | 时钟/频率转换器 |
| PLL： | 是 |
| 主要目的： | 以太网，SONET/SDH |
| 输入： | CMOS，LVDS，LVPECL |
| 输出： | CMOS，HSTL，LVDS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 2:2 |
| 差分 - 输入:输出： | 是/是 |
| 频率 - 最大： | 1.25GHz |
| 电源电压： | 1.71 V ~ 3.465 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-VQ（6x6） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
AD9557
Data Sheet
Rev. B | Page 26 of 92
Program the System Clock and Free Run Tuning Word
The system clock multiplier (SYSCLK) parameters are at
Register 0x0100 to Register 0x0108, and the free run tuning word
is at Register 0x0300 to Register 0x0303. Use the following steps
for optimal performance:
1. Set the system clock PLL input type and divider values.
2. Set the system clock period.
It is essential to program the system clock period because
many of the AD9557 subsystems rely on this value.
3. Set the system clock stability timer.
It is highly recommended that the system clock stability
timer be programmed. This is especially important when
using the system clock multiplier and also applies when
using an external system clock source, especially if the
external source is not expected to be completely stable
when power is applied to the AD9557. The system clock
stability timer specifies the amount of time that the system
clock PLL must be locked before the part declares that the
system clock is stable. The default value is 50 ms.
4. Program the free run tuning word.
The free run frequency of the digital PLL (DPLL) determines
the frequency appearing at the APLL input when free run
mode is selected. The free run tuning word is at Register
0x0300 to Register 0x0303. The correct free run frequency
is required for the APLL to calibrate and lock correctly.
5. Set user free run mode (Register 0x0A01[5] = 1b).
Initialize and Calibrate the Output PLL (APLL)
The registers controlling the APLL are at Register 0x0400 to
Register 0x0408. This low noise, integer-N PLL multiplies the
DPLL output (which is usually 175 MHz to 200 MHz) to a
frequency in the 3.35 GHz to 4.05 GHz range. After the system
clock is configured and the free run tuning word is set in
Register 0x0300 to Register 0x0303, the user can set the manual
APLL VCO calibration bit (Register 0x0405[0]) and issue an I/O
update (Register 0x0005[0]). This process performs the APLL
VCO calibration. VCO calibration ensures that, at the time of
calibration, the dc control voltage of the APLL VCO is centered
in the middle of its operating range. It is important to remember
the following points when calibrating the APLL VCO:
The system clock must be stable.
The APLL VCO must have the correct frequency from
the 30-bit DCO (digitally controlled oscillator) during
calibration.
The APLL VCO must be recalibrated any time the APLL
frequency changes.
APLL VCO calibration occurs on the low-to-high transition
of the manual APLL VCO calibration bit, and this bit is not
autoclearing. Therefore, this bit must be cleared (and an
I/O update issued) before another APLL calibration is started.
The best way to monitor successful APLL calibration is to
monitor Bit 2 in Register 0x0D01 (APLL lock).
Program the Clock Distribution Outputs
The APLL output goes to the clock distribution block. The
clock distribution parameters reside in Register 0x0500 to
Register 0x0509. They include the following:
Output power-down control
Output enable (disabled by default)
Output synchronization
Output mode control
Output divider functionality
See the Clock Distribution section for more information.
Generate the Output Clock
If Register 0x0500[1:0] is programmed for automatic clock
distribution synchronization via the DPLL phase or frequency
lock, the synthesized output signal appears at the clock distribution
outputs. Otherwise, set and then clear the soft sync clock
distribution bit (Register 0x0A02, Bit 1) or use a multifunction
pin input (if programmed for use) to generate a clock distribution
sync pulse, which causes the synthesized output signal to appear
at the clock distribution outputs.
Program the Multifunction Pins (Optional)
This step is required only if the user intends to use any of the
multifunction pins for status or control. The multifunction pin
parameters are at Register 0x0200 to Register 0x0208.
Program the IRQ Functionality (Optional)
This step is required only if the user intends to use the IRQ feature.
The IRQ monitor registers are at Register 0x0D02 to Register
0x0D09. If the desired bits in the IRQ mask registers at Register
0x020A to Register 0x020F are set high, the appropriate IRQ
monitor bit at Register 0x0D02 to Register 0x0D07 is set high
when the indicated event occurs.
Individual IRQ events are cleared by using the IRQ clearing
registers at Register 0x0A04 to Register 0x0A09 or by setting
the clear all IRQs bit (Register 0x0A03[1]) to 1b.
The default values of the IRQ mask registers are such that
interrupts are not generated. The IRQ pin mode default is open-
drain NMOS.
Program the Watchdog Timer (Optional)
This step is required only if the user intends to use the watchdog
timer. The watchdog timer control is in Register 0x0210 and
Register 0x0211 and is disabled by default.
The watchdog timer is useful for generating an IRQ after a fixed
amount of time. The timer is reset by setting the clear watchdog
timer bit (Register 0x0A03[0]) to 1b.
相关PDF资料 |
PDF描述 |
|---|---|
| V375C36M150BG | CONVERTER MOD DC/DC 36V 150W |
| AD9547BCPZ | IC CLOCK GEN/SYNCHRONIZR 64LFCSP |
| D38999/20MF11JN | CONN RCPT 11POS WALL MNT W/SCKT |
| AD9549ABCPZ | IC CLOCK GEN/SYNCHRONIZR 64LFCSP |
| ADN2814ACPZ | IC CLOCK/DATA RECOVERY 32LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9557BCPZ-REEL7 | 功能描述:IC CLK XLATR PLL 1250MHZ 40LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:28 系列:- 类型:时钟/频率发生器 PLL:是 主要目的:Intel CPU 服务器 输入:时钟 输出:LVCMOS 电路数:1 比率 - 输入:输出:3:22 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:64-TFSOP （0.240"，6.10mm 宽） 供应商设备封装:64-TSSOP 包装:管件 |
| AD9558 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad Input Multiservice Line Card Adaptive |
| AD9558/PCBZ | 功能描述:BOARD EVAL FOR AD9558 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| AD9558BCPZ | 功能描述:IC CLOCK TRANSLATOR 64LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:1 系列:- 类型:时钟/频率发生器，多路复用器 PLL:是 主要目的:存储器，RDRAM 输入:晶体 输出:LVCMOS 电路数:1 比率 - 输入:输出:1:2 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:Digi-Reel® 其它名称:296-6719-6 |
| AD9558BCPZ-REEL7 | 功能描述:IC CLK XLATR PLL 1250MHZ 64LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:28 系列:- 类型:时钟/频率发生器 PLL:是 主要目的:Intel CPU 服务器 输入:时钟 输出:LVCMOS 电路数:1 比率 - 输入:输出:3:22 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:64-TFSOP （0.240"，6.10mm 宽） 供应商设备封装:64-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。