- 您现在的位置：买卖IC网 > PDF目录1778 > ADUC7033BSTZ-88-RL (Analog Devices Inc)IC BATT SENSOR PREC 48LQFP PDF资料下载
参数资料
| 型号： | ADUC7033BSTZ-88-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 84/140页 |
| 文件大小： | 0K |
| 描述： | IC BATT SENSOR PREC 48LQFP |
| 标准包装： | 2,000 |
| 功能： | 电池监控器 |
| 电源电压： | 3.5 V ~ 18 V |
| 工作温度： | -40°C ~ 115°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页当前第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页
ADuC7033
TIMER3 OR WATCHDOG TIMER
16-BIT LOAD
LOW POWER
32.768kHz
PRESCALER
1, 16, 256
16-BIT
UP/DOWN COUNTER
WATCHDOG RESET
TIMER3 IRQ
TIMER3
VALUE
Figure 37. Timer3 Block Diagram
Timer3 has two modes of operation, normal mode and
watchdog mode. The watchdog timer is used to recover
from an illegal software state. When enabled, it requires
periodic servicing to prevent it from forcing a reset of the
processor.
Normal Mode
The Timer3 in normal mode is identical to Timer0 in 16-bit
mode of operation, except for the clock source. The clock source
is the low power, 32.768 kHz oscillator scalable by a factor of 1,
16, or 256.
Timer3 Interface
The Timer3 interface consists of four MMRs.
T3LD and T3VAL are 16-bit registers (Bit 0 to Bit 15) and hold
16-bit unsigned integers. T3VAL is read only.
T3CLRI is an 8-bit register. Writing any value to this register
clears the Timer3 interrupt in normal mode or resets a new
timeout period in watchdog mode.
Timer3 Load Register
Timer3 reloads the value from T3LD when Timer3 overflows.
Watchdog Mode
Watchdog mode is entered by setting T3CON[5]. Timer3 decre-
ments from the timeout value present in the T3LD register until
zero. The maximum timeout is 512 seconds, using a maximum
prescaler/256 and full scale in T3LD.
User software should not configure a timeout period of less
than 30 ms. This is to avoid any conflict with Flash/EE memory
page erase cycles that require 20 ms to complete a single page
Name:
Address:
Default Value:
Access:
Function:
T3LD
0xFFFF0360
0x0040
Read/write
This 16-bit MMR holds the Timer3
reload value.
erase cycle and kernel execution.
Timer3 Value Register
If T3VAL reaches 0, a reset or an interrupt occurs, depending
on T3CON[1]. To avoid a reset or an interrupt event, any value
must be written to T3CLRI before T3VAL reaches zero. This
reloads the counter with T3LD and begins a new timeout period.
When watchdog mode is entered, T3LD and T3CON are
write protected. These two registers cannot be modified until
a power-on reset event resets the watchdog timer. After any
other reset event, the watchdog timer continues to count. The
watchdog timer should be configured in the initial lines of user
Name:
Address:
Default Value:
Access:
Function:
T3VAL
0xFFFF0364
0x0040
Read only
This 16-bit, read only MMR holds the current
Timer3 count value.
code to avoid an infinite loop of watchdog resets. User software
Timer3 Clear Register
should only configure a minimum timeout period of 30 ms.
Timer3 is automatically halted during JTAG debug access and
only recommences counting after JTAG has relinquished
control of the ARM7 core. By default, Timer3 continues to
count during power-down. This can be disabled by setting Bit 0
in T3CON. It is recommended to use the default value, that is,
that the watchdog timer continues to count during power-down.
Name:
Address:
Access:
Function:
T3CLRI
0xFFFF036C
Write only
This 16-bit, write-only MMR is written (with
any value) by user code to refresh (reload)
Timer3 in watchdog mode to prevent a
watchdog timer reset event.
Rev. B | Page 84 of 140
相关PDF资料 |
PDF描述 |
|---|---|
| ADUM3070ARQZ | IC REG PUSH-PLL CTRLR ISO 16SSOP |
| AH284-WL-7 | IC HALL FAN CTRLR 500MA SC59-3 |
| AH285-WL-7 | IC HALL FAN CTRLR 400MA SC59-3 |
| AH286-WL-7 | IC HALL FAN CTRLR 400MA SC59-3 |
| AH287-YL-13 | IC HALL FAN CTRLR 500MA SOT89-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7033BSTZ-8L | 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LQFP - Trays 制造商:Rochester Electronics LLC 功能描述: |
| ADUC7033BSTZ-8L-RL | 制造商:Analog Devices 功能描述:INTEGRATED PRECISION BATTERY SENSOR 48LQFP - Tape and Reel |
| ADUC7033BSTZ8VTCRL | 制造商:Analog Devices 功能描述: |
| ADUC7034 | 制造商:AD 制造商全称:Analog Devices 功能描述:Integrated Precision Battery Sensor for Automotive |
| ADUC7034BCPZ | 功能描述:IC MCU FLASH 32K ANLG IO 48LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
发布紧急采购，3分钟左右您将得到回复。