- 您现在的位置：买卖IC网 > PDF目录67685 > ICS1890Y-14 1 CHANNEL(S), 100M bps, SERIAL COMM CONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | ICS1890Y-14 |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 1 CHANNEL(S), 100M bps, SERIAL COMM CONTROLLER, PQFP64 |
| 封装： | TQFP-64 |
| 文件页数： | 23/66页 |
| 文件大小： | 1749K |
| 代理商： | ICS1890Y-14 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
3
ICS1890
Modes of Operation
Reset & Basic Initialization
Reset can be accomplished using either register bit 0:15 or the
RESETpin.
For a hardware reset, RESET must be held at a logic zero level
for at least two clock cycles and may be held low as long as
desired.
While RESET is held low the device is in Low Power mode.
After the RESET pin is released to a logic one level, Low
Power mode is exited, the PHY address is latched into register
16, and the reset process continues to completion.
For a software reset, a management agent must write a logic
one to register bit 0:15. This will start the reset process. The
software reset bit will clear itself automatically when reset is
completed.
All reset timing parameters are specified in the Electricals
section of the data sheet.
Low Power and Automatic 100Base-T Power-
Down
The ICS1890 supports two power saving modes. TheICS1890
device can be placed into a state where very littler power is
drawn by the device. This Low Power mode can be activated
by holding the RESET pin continuously low or by writing a
logic one to the Power-down bit (0:11).
When the device is in Low Power mode, all functions are
disabled except for register access through the MII Management
Interface.
All register values are maintained during Low Power mode,
except for latching status bits, which are reset to their default
values.
The ICS1890 can also automatically reduce its total power
requirementswhenoperatingin10Base-Tmodebyautomatically
powering-down the 100Base-TX modules.
The power required by the ICS1890 in normal, 100Base-TX
power-down, and Low Power modes is given in the Electricals
section of the data sheet.
Auto-Negotiation
A link can automatically be established using Auto-Negotiation.
When enabled, Auto-Negotiation will exchange information
about the local nodes capabilities with its remote link partner.
After the information is exchanged, each device compares its
capabilities with those of its partner and then the highest
performance operational mode is automatically selected.
As an example, if one device supports 10Base-T and 100Base-
TX, and the other device supports 100Base-TX and 100Base-
T4, 100Base-TX will automatically be selected.
See the Auto-Negotiation section for more details on how the
process is initiated and controlled.
100Base-TX
The primary operational mode of the ICS1890 is to provide
100Base-TX physical layer services. This consists mainly of
converting data from parallel to serial at a 100 Mb/s data rate.
The device may be configured in a number of different ways
and also provides detailed operational status information.
10Base-T
The ICS1890 also provides 10Base-T physical layer services
to allow easy migration from 10 to 100 Mb/s service. Complete
data service is provided with configuration and status available
to management.
Full Duplex
The ICS1890 supports either half and full duplex operation
for both 10Base-T and 100Base-TX. Full Duplex operation
allows simultaneous transmission and reception of data which
can effectively double data throughput to 20 or 200 Mb/s.
To operate in Full Duplex mode, some of the standard 10Base-
T and 100Base-TX behaviors are modified.
In 10Base-T Full Duplex mode, transmitted data is not looped
back to the receiver and SQE test is not performed.
In both 10Base-T and 100Base-TX Full Duplex modes, CRS is
asserted in response only to receive activity and COL always
remains inactive.
相关PDF资料 |
PDF描述 |
|---|---|
| ICS2059GI-02 | 27 MHz, VIDEO CLOCK GENERATOR, PDSO16 |
| ICS2304NZGI-1T | 2304 SERIES, LOW SKEW CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| ICS2304NZG-1LF | 2304 SERIES, LOW SKEW CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| ICS252MI-XXLF | 200 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| ICS252MI-XX | 200 MHz, OTHER CLOCK GENERATOR, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS1890Y-4 | 制造商:ICS 功能描述:1890Y-4 |
| ICS1891 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:LAN Transceiver |
| ICS1891Y | 制造商:未知厂家 制造商全称:未知厂家 功能描述:LAN Transceiver |
| ICS1892 | 制造商:ICS 制造商全称:ICS 功能描述:10Base-T/100Base-TX Integrated PHYceiver |
| ICS1892Y | 制造商:ICS 制造商全称:ICS 功能描述:10Base-T/100Base-TX Integrated PHYceiver |
发布紧急采购，3分钟左右您将得到回复。