参数资料
| 型号： | COREFIR-RM |
| 厂商： | Microsemi SoC |
| 文件页数： | 59/67页 |
| 文件大小： | 0K |
| 描述： | IP MODULE COREFIR |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页当前第59页第60页第61页第62页第63页第64页第65页第66页第67页
Tool Flows
For information on using SmartDesign to configure, connect and generate cores, refer to the Libero SoC
Note: A full path to a Libero project that instantiates CoreFIR including the project name must not contain
spaces.
Simulation Flows
The User Testbench for CoreFIR is included in the release.
To run simulations, select the User Testbench flow within SmartDesign. The User Testbench is selected
through the Core Configuration GUI.
When SmartDesign generates the core, it will install the user testbench files.
To run the user testbench, set the design root to the CoreFIR instantiation in the Libero design hierarchy
pane and run Pre-Synthesis design simulation.
Note: When simulating the VHDL version of the core you might want to get rid of the IEEE.NUMERIC_STD
library warnings. To do so add the following two lines to the automatically generated run.do file:
? set NumericStdNoWarnings 1
? set StdArithNoWarnings 1
User Testbench
CoreFIR comes with a user testbench, which can be invoked using the core user interface. Figure 56 depicts
the testbench block diagram. The golden behavioral FIR filter directly implements the appropriate filter
equation for a selected filter type. Both the golden behavioral filter and CoreFIR are configured identically
and receive the same test signal. The testbench compares the output signals of the Golden filter and the
UUT.
CoreFIR
Test Data
Generator
User
Configuration
Compare
Golden
Behavioral
FIR Filter
Figure 56 · CoreFIR User Testbench
The testbench provides examples of how to use generated FIR filter. The testbench can be modified as
needed.
Fully Enumerated User Testbench
The testbench for the Fully Enumerated filter in Reloadable coefficient mode uses the constant coefficient
file to configure the golden behavioral Filter and simulate Reloadable coefficients. To run the user testbench
in Reloadable mode, follow the steps listed below.
60
1.
2.
3.
4.
Enter the desired core configuration. Set Constant Coefficient type.
Create and load constant coefficient file matching the core configuration.
Generate design.
Set Reloadable Coefficient type, generate design, and run simulation.
CoreFIR v8.5 Handbook
相关PDF资料 |
PDF描述 |
|---|---|
| COREPCIF-RM | IP MODULE COREPCIF |
| COREU1LL-AR | IP MODULE COREU1LL |
| COREU1PHY-AR | IP MODULE COREU1PHY |
| CORR-8BIT-XM-UT2 | SITE LICENSE IP CORRELATOR XP |
| CP2-GSA-L | CONN SHIELD LOWER TYPE A 22 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| COREFIR-UR | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:CoreFIR Finite Impulse Response (FIR) Filter Generator |
| COREFIR-XX | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:CoreFIR Finite Impulse Response (FIR) Filter Generator |
| COREMP7 | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:CoreMP7 |
| COREPCI-AN | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:CorePCI v5.41 |
| COREPCI-AR | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:CorePCI v5.41 |
发布紧急采购，3分钟左右您将得到回复。