- 您现在的位置：买卖IC网 > PDF目录11562 > DS3112+W (Maxim Integrated Products)IC MUX T3/E3 3.3V 256-PBGA PDF资料下载
参数资料
| 型号： | DS3112+W |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 63/133页 |
| 文件大小： | 0K |
| 描述： | IC MUX T3/E3 3.3V 256-PBGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 40 |
| 控制器类型： | 调帧器，多路复用器 |
| 接口： | 并行/串行 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 电流 - 电源： | 150mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 256-LBGA |
| 供应商设备封装： | 256-PBGA（27x27） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页当前第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页
DS3112
35 of 133
Bit 4: Manual Error Counter Update (MECU). A zero to one transition on this bit will cause the device to
update the performance error counters. This bit is ignored if the AECU control bit is set low. This bit must be
cleared and set again for a subsequent update. This bit is logically ORed with the external FRMECU hardware
input signal. After this bit has toggled, the host must wait at least 100ns before reading the error counters to allow
the device time to complete the update.
Bit 5: High-Speed (T3/E3) Port Unipolar Enable (UNI). When this bit is set low, the device will output a bipolar
coded signal at HTPOS and HTNEG and expect a bipolar coded signal at HRPOS and HRNEG. When this bit is
set high, the device will output a NRZ coded signal at HTPOS and expect a NRZ coded signal at HRPOS. In the
unipolar mode, the device will force the HTNEG output low and the HRNEG input is ignored and should be tied
low. In the unipolar mode, the B3ZS and HDB3 coder/decoders should be disabled by setting the ZCSD bit to one
(ZCSD = 1).
0 = bipolar mode
1 = unipolar mode
Bit 6: Loss Of Transmit Clock Mux Control (LOTCMC). The DS3112 can detect if the FTCLK fails to
transition. If this bit is set low, the device will take no action (other than setting the LOTC status bit) when the
FTCLK fails to transition. When this bit is set high, the device will automatically switch to the input receive clock
(HRCLK) when the FTCLK fails and transmit AIS.
0 = do not switch to the HRCLK signal if FTCLK fails to transition
1 = automatically switch to the HRCLK signal if the FTCLK fails to transition and send AIS
Bit 7: T3/E3 Transmit Frame Sync I/O Control (FTSOFC). When this bit is set low, the FTSOF signal will be
an output and will pulse for one FTCLK cycle at the beginning of each frame. When this bit is high, the FTSOF
signal is an input and the device uses it to determine the frame boundaries.
0 = FTSOF is an output
1 = FTSOF is an input
Bit 8: Low-Speed (T1/E1) Transmit Port Common Clock Enable (LTCCEN). When this bit is set high, the
LTCLK1 to LTCLK28 and LTCLKA and LTCLKB inputs are ignored and a common clock sourced via the
LTCCLK input is used in their place.
0 = disable LTCCLK
1 = enable LTCCLK
Bit 9: Low-Speed (T1/E1) Receive Port Common Clock Enable (LRCCEN). When this bit is set high, the
LRCLK1 to LRCLK28 and LRCLKA and LRCLKB outputs will all be sourced from the LRCCLK input. This
configuration can only be used in applications where it can be insured that all of the T1 or E1 channels from the far
end are being sourced from a common clock.
0 = disable LRCCLK
1 = enable LRCCLK
Bit 10: High-Speed (T3/E3) Data Enable Mode Select (DENMS). When this bit is set low, the FRDEN and
FTDEN outputs will be asserted during payload data and deasserted during overhead data. When this bit is high,
FRDEN and FTDEN are gapped clocks that pulse during payload data and are suppressed during overhead data.
0 = FRDEN and FTDEN are data enables
1 = FRDEN and FTDEN are gapped clocks
Bit 11: Low-Speed (T1/E1) Port Loop Timed Mode (LLTM). When this bit is set low, the low-speed T1 and E1
receive clocks (LRCLK) are not routed to the transmit side. When this bit is high, the LRCLKs are routed to the
transmit side to be used as the transmit T1 and E1 clocks. When enabled, all the low-speed ports are looped timed.
This control bit affects all the low-speed ports. The device is not capable of setting individual low-speed ports into
and out of looped timed mode. See the block diagram in Figure 1-1 and Figure 1-2 for more details.
0 = disable loop timed mode (LRCLK is not used to replace the associated LTCLK)
1 = enable loop timed mode (LRCLK replaces the associated LTCLK)
相关PDF资料 |
PDF描述 |
|---|---|
| CONREVSMA007-R58 | CONN RP-SMA MALE END CRIMP RG-58 |
| DS26401NA2+ | IC OCTAL FRAMER T1/E1/J1 256BGA |
| VI-24L-IX-S | CONVERTER MOD DC/DC 28V 75W |
| DS26401+ | IC OCTAL FRAMER T1/E1/J1 256BGA |
| PIC16LF1938-E/SS | MCU 8BIT 16K FLASH 28SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3116MP000 | 制造商:Thomas & Betts 功能描述:MAXGARD - RR8F |
| DS311X | 功能描述:KWIK-CHG DESIGNATION STRIPS DBL RoHS:是 类别:盒，外壳，支架 >> 插线台，插座面板 - 配件 系列:Kwik-Change® 标准包装:50 系列:- 附件类型:模拟插头，双 样式:耳机，0.173" 直径 包括:- |
| DS312 | 功能描述:插线板 DESIGN STRIP COVER RoHS:否 制造商:Switchcraft 产品类型:Bantam (TT) 正规化: 高度/机架数量: 深度: 端接类型: 位置/触点数量:48 |
| DS-312 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Four-Way Power Divider, 10 - 500 MHz |
| DS312_09 | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-3E FPGA Family: Introduction and Ordering Information |
发布紧急采购，3分钟左右您将得到回复。