- 您现在的位置：买卖IC网 > PDF目录11562 > DS3112+W (Maxim Integrated Products)IC MUX T3/E3 3.3V 256-PBGA PDF资料下载
参数资料
| 型号： | DS3112+W |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 87/133页 |
| 文件大小： | 0K |
| 描述： | IC MUX T3/E3 3.3V 256-PBGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 40 |
| 控制器类型： | 调帧器，多路复用器 |
| 接口： | 并行/串行 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 电流 - 电源： | 150mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 256-LBGA |
| 供应商设备封装： | 256-PBGA（27x27） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页当前第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页
DS3112
57 of 133
Table 5-2. E3 Alarm Criteria
ALARM/
CONDITION
DEFINITION
SET CRITERIA
CLEAR CRITERIA
AIS
Alarm Indication Signal
Unframed all ones
Four or fewer zeros in
two consecutive 1536-
bit frames
Five or more zeros in two
consecutive 1536-bit frames
LOS
Loss Of Signal
(See note)
192 consecutive zeros
No EXZ events over a 192-bit
window that starts with the
first one received
LOF
Loss Of Frame
Too many FAS errors
Four consecutive bad
FAS
Three consecutive good FAS
RAI
Remote Alarm Indication
Inactive: Bit 11 of the frame = 0
Active: Bit 11 of the frame = 1
Bit 11 = 1 for 4
consecutive frames
(6144 bits/179s)
Bit 11 = 0 for 4 consecutive
frames (6144 bits/179s)
Note: LOS is not defined for unipolar (binary) operation.
Register Name:
T3E3INFO
Register Description:
T3/E3 Information Register
Register Address:
16h
Bit #
7
6
5
4
3
2
1
0
Name
—
SEFE
EXZ
MBE
FBE
ZSCD
COFA
Default
—
Bit #
15
14
13
12
11
10
9
8
Name
—
RAIC
AISC
LOFC
LOSC
T3AIC
E3Sn
Default
—
Note: Bits that are underlined are read-only; all other bits are read-write. The status bits in the T3E3INFO cannot cause a hardware
interrupt to occur.
Bit 0: Change Of Frame Alignment Detected (COFA). This latched read-only event-status bit will be set to a
one when the T3/E3 framer has experienced a change of frame alignment (COFA). A COFA occurs when the
device achieves synchronization in a different alignment than it had previously. If the device has never acquired
synchronization before, then this status bit is meaningless. This bit will be cleared when read and will not be set
again until the framer has lost synchronization and reacquired synchronization in a different alignment.
Bit 1: Zero Suppression Codeword Detected (ZSCD). This latched read-only event-status bit will be set to a one
when the T3/E3 framer has detected a B3ZS/HDB3 codeword. This bit will be cleared when read and will not be
set again until the framer has detected another B3ZS/HDB3 codeword.
Bit 2: F-Bit or FAS Error Detected (FBE). This latched read-only status bit will be set to a one when the DS3112
has detected an error in either the F bits (T3 mode) or the FAS word (E3 mode). This bit will be cleared when read
and will not be set again until the device detects another error.
Bit 3: M-Bit Error Detected (MBE). This latched read-only event status bit will be set to a one when the DS3112
has detected an error in the M bits. This bit will be cleared when read and will not be set again until the device
detects another error in one of the M bits. This status bit has no meaning in the E3 mode and should be ignored.
Bit 4: Excessive Zeros Detected (EXZ). This latched read-only event status bit will be set to a one each time the
DS3112 has detected a consecutive string of either three or more zeros (T3 mode) or four or more zeros (E3 mode).
This bit will be cleared when read and will not be set again until the device detects another EXcessive Zero event.
相关PDF资料 |
PDF描述 |
|---|---|
| CONREVSMA007-R58 | CONN RP-SMA MALE END CRIMP RG-58 |
| DS26401NA2+ | IC OCTAL FRAMER T1/E1/J1 256BGA |
| VI-24L-IX-S | CONVERTER MOD DC/DC 28V 75W |
| DS26401+ | IC OCTAL FRAMER T1/E1/J1 256BGA |
| PIC16LF1938-E/SS | MCU 8BIT 16K FLASH 28SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3116MP000 | 制造商:Thomas & Betts 功能描述:MAXGARD - RR8F |
| DS311X | 功能描述:KWIK-CHG DESIGNATION STRIPS DBL RoHS:是 类别:盒，外壳，支架 >> 插线台，插座面板 - 配件 系列:Kwik-Change® 标准包装:50 系列:- 附件类型:模拟插头，双 样式:耳机，0.173" 直径 包括:- |
| DS312 | 功能描述:插线板 DESIGN STRIP COVER RoHS:否 制造商:Switchcraft 产品类型:Bantam (TT) 正规化: 高度/机架数量: 深度: 端接类型: 位置/触点数量:48 |
| DS-312 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Four-Way Power Divider, 10 - 500 MHz |
| DS312_09 | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-3E FPGA Family: Introduction and Ordering Information |
发布紧急采购，3分钟左右您将得到回复。