- 您现在的位置：买卖IC网 > PDF目录20639 > ADE7878ACPZ (Analog Devices Inc)IC ENERGY METERING 3PH 40LFCSP PDF资料下载
参数资料
| 型号： | ADE7878ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 27/100页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 3PH 40LFCSP |
| 标准包装： | 1 |
| 输入阻抗： | 400 千欧 |
| 测量误差： | 0.2% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.4V |
| 电源电压： | 2.4 V ~ 3.7 V |
| 测量仪表类型： | 3 相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-WQ（6x6） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
Data Sheet
HARDWARE RESET
The ADE7854 / ADE7858 / ADE7868 / ADE7878 each has a RESET
pin. If the ADE7854 , ADE7858 , ADE7868 , or ADE7878 is in
PSM0 mode and the RESET pin is set low, then the ADE78xx
enters the hardware reset state. The ADE78xx must be in PSM0
mode for a hardware reset to be considered. Setting the RESET
pin low while the ADE78xx is in PSM1, PSM2, and PSM3
modes does not have any effect.
If the ADE7854 , ADE7858 , ADE7868 , or ADE7878 is in PSM0
mode and the RESET pin is toggled from high to low and then
back to high after at least 10 μs, all the registers are set to their
default values, including the CONFIG2 and LPOILVL registers.
The ADE78xx signals the end of the transition period by triggering
the IRQ1 interrupt pin low and setting Bit 15 (RSTDONE) in the
STATUS1 register to 1. This bit is 0 during the transition period
and becomes 1 when the transition ends. The status bit is cleared
and the IRQ1 pin is returned high by writing to the STATUS1
register with the corresponding bit set to 1.
After a hardware reset, the DSP is in idle mode, which means it
does not execute any instruction.
state. If SPI is the port used by the external microprocessor, the
procedure to enable it must be repeated immediately after the
RESET pin is toggled back to high (see the Serial Interfaces
section for details).
ADE7854/ADE7858/ADE7868/ADE7878
SOFTWARE RESET FUNCTIONALITY
Bit 7 (SWRST) in the CONFIG register manages the software
reset functionality in PSM0 mode. The default value of this bit is 0.
ADE7878 enter the software reset state. In this state, almost all
internal registers are set to their default values. In addition, the
choice of which serial port, I 2 C or SPI, is in use remains unchanged
if the lock-in procedure has been executed previously (see the
Serial Interfaces for details). The registers that maintain their
values despite the SWRST bit being set to 1 are the CONFIG2
and LPOILVL registers. When the software reset ends, Bit 7
(SWRST) in the CONFIG register is cleared to 0, the IRQ1
interrupt pin is set low, and Bit 15 (RSTDONE) in the STATUS1
register is set to 1. This bit is 0 during the transition period and
becomes 1 when the transition ends. The status bit is cleared and
the IRQ1 pin is set back high by writing to the STATUS1 register
with the corresponding bit set to 1.
After a software reset ends, the DSP is in idle mode, which
means it does not execute any instruction. It is recommended
registers and then enable the data memory RAM protection and
write 0x0001 into the run register to start the DSP (see the
RAM protection and the run register).
Software reset functionality is not available in PSM1, PSM2, or
PSM3 mode.
At this point, it is recommended to initialize all of the ADE78xx
registers, enable data memory RAM protection, and then write
0x0001 into the run register to start the DSP. See the Digital
protection and the run register.
Rev. H | Page 27 of 100
相关PDF资料 |
PDF描述 |
|---|---|
| GBC06DREI-S13 | CONN EDGECARD 12POS .100 EXTEND |
| VI-J60-CX-F4 | CONVERTER MOD DC/DC 5V 75W |
| ECA10DCBT | CONN EDGECARD 20POS R/A .125 SLD |
| EL7242CSZ-T13 | IC DRIVER MOSFET DUAL HS 8-SOIC |
| ADE7169ASTZF16 | IC ENERGY METER 1PHASE 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7878ACPZ | 制造商:Analog Devices 功能描述:IC MULTIFUNCTION ENERGY METERING LFCSP40 |
| ADE7878ACPZ-RL | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7878XCPZ | 制造商:Analog Devices 功能描述:POLY PHASE MULTIFUNCTION ENERGY METERING IC WITH TOTAL - Bulk |
| ADE7880 | 制造商:Analog Devices 功能描述:BOARD EVAL ENERGY METER ADE |
| ADE7880ACPZ | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
发布紧急采购，3分钟左右您将得到回复。