- 您现在的位置：买卖IC网 > PDF目录20639 > ADE7878ACPZ (Analog Devices Inc)IC ENERGY METERING 3PH 40LFCSP PDF资料下载
参数资料
| 型号： | ADE7878ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 64/100页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 3PH 40LFCSP |
| 标准包装： | 1 |
| 输入阻抗： | 400 千欧 |
| 测量误差： | 0.2% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.4V |
| 电源电压： | 2.4 V ~ 3.7 V |
| 测量仪表类型： | 3 相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-WQ（6x6） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页当前第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
APNOLOAD =
× NOLOAD × PMAX
V n I
ADE7854/ADE7858/ADE7868/ADE7878
REACTIVE
ENERGY
NO-LOAD
THRESHOLD
REACTIVE
POWER
NO-LOAD
THRESHOLD
NO-LOAD
THRESHOLD
ACTIVE
POWER
REVRPx BIT
IN STATUS0
xVARSIGN BIT
IN PHSIGN
VARNOLOAD POS NEG POS
SIGN = POSITIVE
Figure 81. Reactive Power Accumulation in Sign Adjusted Mode
Sign of Sum-of-Phase Powers in the CFx Datapath
The ADE7854 / ADE7858 / ADE7868 / ADE7878 have sign
detection circuitry for the sum of phase powers that are used in
the CFx datapath. As seen in the beginning of the Energy-to-
Frequency Conversion section, the energy accumulation in the
CFx datapath is executed in two stages. Every time a sign change is
detected in the energy accumulation at the end of the first stage,
that is, after the energy accumulated into the accumulator
reaches one of the WTHR, VARTHR, or VATHR thresholds, a
dedicated interrupt can be triggered synchronously with the
corresponding CFx pulse. The sign of each sum can be read in
the PHSIGN register.
Bit 18, Bit 13, and Bit 9 (REVPSUM3, REVPSUM2, and
REVPSUM1, respectively) of the STATUS0 register are set
to 1 when a sign change of the sum of powers in CF3, CF2,
or CF1 datapaths occurs. To correlate these events with the
pulses generated at the CFx pins, after a sign change occurs,
Bit REVPSUM3, Bit REVPSUM2, and Bit REVPSUM1 are set
in the same moment in which a high-to-low transition at the
CF3, CF2, and CF1 pin, respectively, occurs.
Bit 8, Bit 7, and Bit 3 (SUM3SIGN, SUM2SIGN, and SUM1SIGN,
respectively) of the PHSIGN register are set in the same moment
with Bit REVPSUM3, Bit REVPSUM2, and Bit REVPSUM1 and
indicate the sign of the sum of phase powers. When cleared to
0, the sum is positive. When set to 1, the sum is negative.
Interrupts attached to Bit 18, Bit 13, and Bit 9 (REVPSUM3,
REVPSUM2, and REVPSUM1, respectively) in the STATUS0
register are enabled by setting Bit 18, Bit 13, and Bit 9 in the
MASK0 register. If enabled, the IRQ0 pin is set low, and the
status bit is set to 1 whenever a change of sign occurs. To find
the phase that triggered the interrupt, the PHSIGN register is
read immediately after reading the STATUS0 register. Next, the
status bit is cleared, and the IRQ0 pin is set high again by writing
to the STATUS0 register with the corresponding bit set to 1.
Data Sheet
NO LOAD CONDITION
The no load condition is defined in metering equipment standards
as occurring when the voltage is applied to the meter and no cur-
rent flows in the current circuit. To eliminate any creep effects in
the meter, the ADE7854 / ADE7858 / ADE7868 / ADE7878 contain
three separate no load detection circuits: one related to the total
only), one related to the fundamental active and reactive powers
No Load Detection Based On Total Active, Reactive
Powers
This no load condition is triggered when the absolute values of
both phase total active and reactive powers are less than or equal
to positive thresholds indicated in the respective APNOLOAD
and VARNOLOAD signed 24-bit registers. In this case, the total
active and reactive energies of that phase are not accumulated
and no CFx pulses are generated based on these energies. The
APNOLOAD register represents the positive no load level of
active power relative to PMAX, the maximum active power
obtained when full-scale voltages and currents are provided at
ADC inputs. The VARNOLOAD register represents the positive
no load level of reactive power relative to PMAX. The expres-
sion used to compute APNOLOAD signed 24-bit value is
(47)
V FS I FS
where:
PMAX = 33,516,139 = 0x1FF6A6B, the instantaneous power
computed when the ADC inputs are at full scale.
V FS , I FS are the rms values of phase voltages and currents when
the ADC inputs are at full scale.
V n is the nominal rms value of phase voltage.
I NOLOAD is the minimum rms value of phase current the meter
starts measuring.
The VARNOLOAD register usually contains the same value as
the APNOLOAD register. When APNOLOAD and VARNOLOAD
are set to negative values, the no load detection circuit is disabled.
Note that the ADE7854 measures only the total active powers.
To ensure good functionality of the ADE7854 no-load circuit,
set the VARNOLOAD register at 0x800000.
section, the serial ports of the ADE78xx work on 32-, 16-, or
8-bit words and the DSP works on 28 bits. APNOLOAD and
VARNOLOAD 24-bit signed registers are accessed as 32-bit
registers with the four MSBs padded with 0s and sign extended
to 28 bits. See Figure 35 for details.
Bit 0 (NLOAD) in the STATUS1 register is set when this no
load condition in one of the three phases is triggered. Bits[2:0]
(NLPHASE[2:0]) in the PHNOLOAD register indicate the state
of all phases relative to a no load condition and are set simulta-
neously with Bit NLOAD in the STATUS1 register. NLPHASE[0]
indicates the state of Phase A, NLPHASE[1] indicates the state
Rev. H | Page 64 of 100
相关PDF资料 |
PDF描述 |
|---|---|
| GBC06DREI-S13 | CONN EDGECARD 12POS .100 EXTEND |
| VI-J60-CX-F4 | CONVERTER MOD DC/DC 5V 75W |
| ECA10DCBT | CONN EDGECARD 20POS R/A .125 SLD |
| EL7242CSZ-T13 | IC DRIVER MOSFET DUAL HS 8-SOIC |
| ADE7169ASTZF16 | IC ENERGY METER 1PHASE 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7878ACPZ | 制造商:Analog Devices 功能描述:IC MULTIFUNCTION ENERGY METERING LFCSP40 |
| ADE7878ACPZ-RL | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7878XCPZ | 制造商:Analog Devices 功能描述:POLY PHASE MULTIFUNCTION ENERGY METERING IC WITH TOTAL - Bulk |
| ADE7880 | 制造商:Analog Devices 功能描述:BOARD EVAL ENERGY METER ADE |
| ADE7880ACPZ | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
发布紧急采购，3分钟左右您将得到回复。