- 您现在的位置：买卖IC网 > PDF目录20639 > ADE7878ACPZ (Analog Devices Inc)IC ENERGY METERING 3PH 40LFCSP PDF资料下载
参数资料
| 型号： | ADE7878ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 52/100页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 3PH 40LFCSP |
| 标准包装： | 1 |
| 输入阻抗： | 400 千欧 |
| 测量误差： | 0.2% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.4V |
| 电源电压： | 2.4 V ~ 3.7 V |
| 测量仪表类型： | 3 相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-WQ（6x6） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页当前第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
ADE7854/ADE7858/ADE7868/ADE7878
ZXSEL[0] IN
LCYCMODE[7:0]
ZERO-
CROSSING
DETECTION
(PHASE A)
Data Sheet
Because the active power is integrated on an integer number of
half-line cycles in this mode, the sinusoidal components are
reduced to 0, eliminating any ripple in the energy calculation.
Therefore, total energy accumulated using the line cycle
ZXSEL[1] IN
LCYCMODE[7:0]
LINECYC[15:0]
accumulation mode is
ZERO-
CROSSING
DETECTION
CALIBRATION
CONTROL
e =
t + nT ∞
∫ p ( t ) dt = nT ∑ V k I k
t k = 1
cos( φ k – γ k )
(28)
(PHASE B)
ZXSEL[2] IN
LCYCMODE[7:0]
ZERO-
CROSSING
DETECTION
(PHASE C)
AWATTOS
where nT is the accumulation time.
Note that line cycle active energy accumulation uses the same
signal path as the active energy accumulation. The LSB size of
these two methods is equivalent.
AWGAIN
OUTPUT
FROM LPF2
ACCUMULATOR
WTHR[47:0]
AWATTHR[31:0]
32-BIT
REGISTER
The ADE7858 / ADE7868 / ADE7878 can compute the total
reactive power on every phase. Total reactive power integrates
all fundamental and harmonic components of the voltages and
currents. The ADE7878 also computes the fundamental reactive
Figure 70. Line Cycle Active Energy Accumulation Mode
The line cycle energy accumulation mode is activated by setting
Bit 0 (LWATT) in the LCYCMODE register. The energy accu-
mulation over an integer number of half line cycles is written
to the watt-hour accumulation registers after LINECYC number
of half line cycles is detected. When using the line cycle
accumulation mode, the Bit 6 (RSTREAD) of the LCYCMODE
register should be set to Logic 0 because the read with reset of
watt-hour registers is not available in this mode.
Phase A, Phase B, and Phase C zero crossings are, respectively,
included when counting the number of half line cycles by setting
power, the power determined only by the fundamental
components of the voltages and currents.
A load that contains a reactive element (inductor or capacitor)
produces a phase difference between the applied ac voltage and
the resulting current. The power associated with reactive elements
is called reactive power, and its unit is VAR. Reactive power is
defined as the product of the voltage and current waveforms when
all harmonic components of one of these signals are phase
shifted by 90°.
Equation 31 gives an expression for the instantaneous reactive
power signal in an ac system when the phase of the current
channel is shifted by +90°.
v ( t ) = ∑ V k 2 sin( kωt + φ k )
i ( t ) = ∑ I k 2 sin ( k ω t + γ k )
i ' ( t ) = ∑ I k 2 sin ? ? k ω t + γ k +
π ?
2 ?
Bits[5:3] (ZXSEL[x]) in the LCYCMODE register. Any combi-
nation of the zero crossings from all three phases can be used
for counting the zero crossing. Select only one phase at a time
for inclusion in the zero crossings count during calibration.
The number of zero crossings is specified by the LINECYC 16-bit
unsigned register. The ADE78xx can accumulate active power
for up to 65,535 combined zero crossings. Note that the internal
∞
k = 1
∞
k = 1
∞
k = 1 ?
?
(29)
(30)
zero-crossing counter is always active. By setting Bit 0 (LWATT)
in the LCYCMODE register, the first energy accumulation
result is, therefore, incorrect. Writing to the LINECYC register
when the LWATT bit is set resets the zero-crossing counter, thus
ensuring that the first energy accumulation result is accurate.
where i?(t) is the current waveform with all harmonic
components phase shifted by 90°.
Next, the instantaneous reactive power, q(t), can be expressed as
q(t) = v(t) × i?(t) (31)
q ( t ) = ∑ V k I k × 2 sin( kωt + φ k ) × sin( kωt + γ k +
π
∑ V k I m × 2sin( kωt + φ k ) × sin( mωt + γ m +
At the end of an energy calibration cycle, Bit 5 (LENERGY) in
the STATUS0 register is set. If the corresponding mask bit in
the MASK0 interrupt mask register is enabled, the IRQ0 pin
also goes active low. The status bit is cleared and the IRQ0 pin is
set to high again by writing to the STATUS0 register with the
corresponding bit set to 1.
∞
k ≠ m
∞
k = 1
k , m = 1 2
)
π
2
)+
Rev. H | Page 52 of 100
相关PDF资料 |
PDF描述 |
|---|---|
| GBC06DREI-S13 | CONN EDGECARD 12POS .100 EXTEND |
| VI-J60-CX-F4 | CONVERTER MOD DC/DC 5V 75W |
| ECA10DCBT | CONN EDGECARD 20POS R/A .125 SLD |
| EL7242CSZ-T13 | IC DRIVER MOSFET DUAL HS 8-SOIC |
| ADE7169ASTZF16 | IC ENERGY METER 1PHASE 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7878ACPZ | 制造商:Analog Devices 功能描述:IC MULTIFUNCTION ENERGY METERING LFCSP40 |
| ADE7878ACPZ-RL | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7878XCPZ | 制造商:Analog Devices 功能描述:POLY PHASE MULTIFUNCTION ENERGY METERING IC WITH TOTAL - Bulk |
| ADE7880 | 制造商:Analog Devices 功能描述:BOARD EVAL ENERGY METER ADE |
| ADE7880ACPZ | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
发布紧急采购，3分钟左右您将得到回复。