- 您现在的位置：买卖IC网 > PDF目录69326 > S1S60000F00A100 1 CHANNEL(S), 2M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | S1S60000F00A100 |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 1 CHANNEL(S), 2M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100 |
| 封装： | 14 X 14 MM, 1.40 MM HEIGHT, PLASTIC, QFP15-100 |
| 文件页数： | 52/83页 |
| 文件大小： | 1024K |
| 代理商： | S1S60000F00A100 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页当前第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页
S1S60000 Technical Manual
50
EPSON
Rev.1.5
5.2.25
COMN0,COMN1,COMN2,COMN3
(Community Name: offset 24h to 27h)
It holds community name that can be set to the SNMP agent. Initial values and set values of respective registers
are as shown in Table 5.12.
The default community name of the SNMP agent is “public” irrespective of values
of the built-in registers.
Table 5.12
Setting of SNMP Community Name
Target
Initial value
Notation in hex
Register setting
Offset
Community name
public
70.75.62.6C.69.63.00.00
COMN0=7570h,
COMN1=6C62h,
COMN2=6369h,
COMN3=0000h
24h
25h
26h
27h
5.3
GPIO
As GPIO (General Purpose Input/Output), S1S60000 has 16 GPIO pins of GPIO[7:0] and GPIO[15:8].
Each
pin allows independent operation.
Special functions other than the GPIO function are assigned to some pins.
You can switch the functions by changing setting of the GPALT register.
After the reset, every pin usable as GPIO is set for the input and the output value is initialized to 0.
When an
output operation is conducted on a pin being specified set for input, the specified data is set as a requested output
value but actual output is not generated.
If the pin is set as an output pin after that, the specified value will be
output from the pin.
When you want to maintain the GPIO output at HIGH level after the hardware reset, set
the level of the pins currently being reset at HIGH by use of the external pull-up register and then select 1 for the
output setting.
Table 5.13
GPIO Pin Functions
Pin name
Characteristics
(*1)
Special function
Priority
GPIO0/INT0
5V tolerant input
Interrupt notice/return from sleep mode
1
GPIO1
5V tolerant input
1
GPIO2/CRS
5V tolerant input
CRS input
1
GPIO3
5V tolerant input
2
GPIO4
5V tolerant input
3
GPIO5
5V tolerant input
3
GPIO6
5V tolerant input
3
GPIO7/OSCCTL
5V tolerant input
Control of external OSC
3
GPIO8/RXD
3.3V schmitt input
Serial Interface
2
GPIO9/TXD
3.3V schmitt input
Serial Interface
2
GPIO10/MODE
3.3V schmitt input
Serial Interface
2
GPIO11/RSV1
3.3V schmitt input
Serial Interface
2
GPIO12/CTS#
3.3V schmitt input
Serial Interface
1
GPIO13/DSR#
3.3V schmitt input
Serial Interface
1
GPIO14/RTS#
3.3V schmitt input
Serial Interface
1
GPIO15/DTR#
3.3V schmitt input
Serial Interface
1
*1
Every pin conforms to CMOS input/output.
Priority indicates the order of operation when two or more pins are to be operated at the same time.
Switching
occurs at the same time among the pins with the same priority level.
Among the pins with different priority
levels, however, there occurs some differences in input and output (due to the time required for the
software-based operation).
If you want such pins to change at the same time, an additional arrangement such as
an external latch to be operated by GPIO is required.
When the INT0 function is enabled, GPIO0 can be used as the Low level input interrupt pin.
This interrupt
takes the S1S60000 out of the sleep mode.
Also, when the DDSTEN bit of the GENCR register is set to “1”,
the notice packet can be sent to the preset network connection destination. For more details, please refer to “5.3.1
Interrupt Notice Function”.
相关PDF资料 |
PDF描述 |
|---|---|
| S202T01 | TRIGGER OUTPUT SOLID STATE RELAY, 3000 V ISOLATION-MAX |
| S102T01 | TRIGGER OUTPUT SOLID STATE RELAY, 3000 V ISOLATION-MAX |
| S3C4510BXX-QE | 32-BIT, 50 MHz, RISC MICROCONTROLLER, PQFP208 |
| S3C72E8XX-QX | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP100 |
| S3C72N4XX-QT | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S1S60000F00A300 | 制造商:Epson Electronics America Inc 功能描述:IC NETWORK CONTROLLER |
| S1S60000F00A30B | 制造商:Epson Electronics America Inc 功能描述:IC NETWORK CONTROLLER |
| S1S60000F00A500 | 制造商:Epson Electronics America Inc 功能描述:IC NETWORK CONTROLLER |
| S1S65000F00A100 | 功能描述:IC WEB CAMERA 128-QFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| S1S65010 | 制造商:EPSON 制造商全称:EPSON 功能描述:Network Camera Controller with JPEG Encoder |
发布紧急采购，3分钟左右您将得到回复。