- 您现在的位置：买卖IC网 > Datasheet目录307 > ADE7569ASTZF16 (Analog Devices Inc)IC ENERGY METER MCU 16K 64LQFP Datasheet资料下载
参数资料
| 型号： | ADE7569ASTZF16 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 123/136页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER MCU 16K 64LQFP |
| 标准包装： | 1 |
| 输入阻抗： | * |
| 测量误差： | * |
| 电压 - 高输入/输出： | * |
| 电压 - 低输入/输出： | * |
| 电流 - 电源： | * |
| 电源电压： | * |
| 测量仪表类型： | * |
| 工作温度： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页当前第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页
Preliminary Technical Data
SS (Slave Select Pin)
In SPI slave mode, a transfer is initiated by the assertion of SS
low. The SPI port then transmits and receives 8-bit data until
the data is concluded by the deassertion of SS. In slave mode, SS
AUTO_SS = 1
SS
SCLK
ADE7566/ADE7569
is always an input.
SPICONT = 1
DIN
DIN1
DIN2
In SPI master mode, the SS can be used to control data transfer
to a slave device. In the automatic slave select control mode, the
SS is asserted low to select the slave device and then raised to
DOUT
DOUT1
DOUT2
deselect the slave device after the transfer is complete. Automatic
slave select control is enabled by setting the AUTO_SS bit in the
SPI Configuration Register SFR (SPIMOD1, 0xE8).
In a multimaster system, the SS can be configured as an input so
that the SPI peripheral can operate as a slave in some situations
AUTO_SS = 1
SS
SCLK
and as a master in others. In this case, the slave selects for the
SPICONT = 0
DIN
DIN1
DIN2
slaves controlled by this SPI peripheral should be generated
with general I/O pins.
SPI MASTER OPERATING MODES
DOUT
DOUT1
DOUT2
The double buffered receive and transmit registers can be used to
maximize the throughput of the SPI peripheral by continuously
streaming out data in master mode. The continuous transmit mode
is designed to use the full capacity of the SPI. In this mode, the
master transmits and receives data until the SPI/I 2 C Transmit
AUTO_SS = 0
SS
SCLK
Buffer SFR (SPI2CTx, 0x9A) is empty at the start of a byte
transfer. Continuous mode is enabled by setting the SPICONT bit
SPICONT = 0
(MANUAL SS CONTROL)
DIN
DIN1
DIN2
in the SPI Configuration Register SFR (SPIMOD2, 0xE9).The
SPI peripheral also offers a single byte read and a single byte
write function.
DOUT
DOUT1
DOUT2
In master mode, the type of transfer is handled automatically,
depending on the configuration of the TIMODE and SPICONT
bits in the SPI Configuration Register SFR (SPIMOD2, 0xE9).
Table 139 shows the sequence of events that should be performed
for each master operating mode. Based on the SS configuration,
some of these events take place automatically.
Figure 95 shows the SPI output for certain automatic chip select
and continuous mode selections. Note that if the continuous
mode is not used, a short delay is inserted between transfers.
Table 139. Procedures for Using SPI as a Master
SPIMOD2[7] =
Figure 95. Automatic Chip Select and Continuous Mode Output
Note that reading the content of the SPI/I 2 C Receive Buffer SFR
(SPI2CRx, 0x9B) should be done using a 2-cycle instruction set
such as MOV A or SPI2CRX. Using a 3-cycle instruction such
as MOV 0x3D or SPI2CRX will not transfer the right
information into the target register.
Mode
Single Byte Write
Continuous
SPICONT Bit
0
1
Description of Operation
Step 1. Write to SPI2CTx SFR.
Step 2.
SS is asserted low and a write routine is initiated.
Step 3. SPITxIRQ interrupt flag is set when SPI2CTx register is empty.
Step 4.
SS is deasserted high.
Step 5. Write to SPI2CTx SFR to clear SPITxIRQ interrupt flag.
Step 1. Write to SPI2CTx SFR.
Step 2.
SS is asserted low and write routine is initiated.
Step 3.
Wait for SPITxIRQ interrupt flag to write to SPI2CTx SFR.
Transfer continues until the SPI2CTx register and transmit shift registers are empty.
Step 4. SPITxIRQ interrupt flag is set when SPI2CTx register is empty.
Step 5.
SS is deasserted high.
Step 6. Write to SPI2CTx SFR to clear SPITxIRQ interrupt flag.
Rev. PrA | Page 123 of 136
相关PDF资料 |
PDF描述 |
|---|---|
| ADE7752BARWZ-RL | IC ENERGY METERING 3PHASE 24SOIC |
| ADE7755ARSZ | IC ENERGY METERING 1PHASE 24SSOP |
| ADE7757ARNZRL | IC ENERGY METERING 1PHASE 16SOIC |
| ADE7758ARWZRL | IC ENERGY METERING 3PHASE 24SOIC |
| ADE7761AARSZ-RL | IC ENERGY METERING 1PHASE 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7569ASTZF162 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE7569ASTZF16-RL | 功能描述:IC ENERGY METER 1PHASE 64-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7569ASTZF16-RL2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE7751 | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection |
| ADE7751AAN-REF | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection |
发布紧急采购，3分钟左右您将得到回复。