- 您现在的位置：买卖IC网 > Datasheet目录307 > ADE7569ASTZF16 (Analog Devices Inc)IC ENERGY METER MCU 16K 64LQFP Datasheet资料下载
参数资料
| 型号： | ADE7569ASTZF16 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 98/136页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER MCU 16K 64LQFP |
| 标准包装： | 1 |
| 输入阻抗： | * |
| 测量误差： | * |
| 电压 - 高输入/输出： | * |
| 电压 - 低输入/输出： | * |
| 电流 - 电源： | * |
| 电源电压： | * |
| 测量仪表类型： | * |
| 工作温度： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页当前第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页
ADE7566/ADE7569
PROTECTING THE FLASH
Preliminary Technical Data
The sequence for writing the protection bits is as follows:
Two forms of protection are offered for this flash memory: read
protection and write/erase protection. The read protection
ensures that any pages that are read protected are not able to be
read by the end user. The write protection ensures that the flash
memory cannot be erased or written over. This protects the end
system from tampering and can prevent the code from being
overwritten in the event of a unexpected disruption of the
normal execution of the program.
Write/erase protection is individually selectable for all of the
32 pages. Read protection is selected in groups of 4 pages (see
Figure 79 for the groupings). The protection bits are stored in
the last flash memory locations, Address 0x3FFA through
Address 0x3FFF (see Figure 81); 4 bytes are reserved for
write/erase protection, 1 byte is for read protection, and another
byte sets the protection security key. The user must enable read
and write/erase protection for the last page for the entire
protection scheme to work.
Note that the read protection does not prevent MOVC
commands to be executed within the code.
There is an additional layer of protection offered by a protection
security key. The user can set up this security key so that the
protection scheme cannot be changed without this key. Once
the protection key has been configured, it cannot be modified.
Enabling Flash Protection by Code
1.
2.
3.
4.
5.
Set up the EADRH, EADRL, PROTB1, and PROTB0
registers with the write/erase protection bits. When erased,
the protection bits default to 1 (like any other bit of flash
memory). The default protection setting is for no
protection. To enable protection, write a 0 to the bits
corresponding to the pages that should be protected.
Set up the PROTR register with the read protection bits.
Note that every read protection bit protects four pages. To
enable the read protection bit, write a 0 to the bits that
should be read protected.
To enable the protection key, write to the PROTKY
register. If enabled, the protection key is required to modify
the protection scheme. The protection key, Flash Memory
Address 0x3FFA, defaults to 0xFF; if the PROTKY register
is not written to, it remains 0xFF. If the protection key is
written to, the PROTKY register must be written with this
value every time the protection functionality is accessed.
Note that once the protection key is configured, it cannot
be modified. Also note that the most significant bit of
Address 0x3FFA is used to enable a lock mechanism for the
watchdog settings (see the Watchdog Timer section for
more information).
Run the protection command by writing 0x0 to the ECON
register.
Reset the chip to activate the new protection.
The protection bytes in the flash memory can be programmed
using flash controller command and programming ECON to 0x08.
In this case, the EADRH, EADRL, PROTB1, and PROTB0 bytes
are used to store the data to be written to the 32 bits of write
protection. Note that the EADRH and EADRL registers are not
used as data pointers here, but to store write protection data.
To enable read and write/erase protection for the last page only,
use the following 8051 code. Writing the flash protection
command to the ECON register initiates programming the
protection bits in the flash.
; enable write/erase protection on the last page only
MOV EADRH, #07FH
EADRH
EADRL
PROTB1
PROTB0
0x3FFF
0x3FFE
0x3FFD
0x3FFC
WP
31
WP
23
WP
15
WP
7
WP
30
WP
22
WP
14
WP
6
WP
29
WP
21
WP
13
WP
5
WP
28
WP
20
WP
12
WP
4
WP
27
WP
19
WP
11
WP
3
WP
26
WP
18
WP
10
WP
2
WP
25
WP
17
WP
9
WP
1
WP
24
WP
16
WP
8
WP
0
MOV EADRL, #0FFH
MOV PROTB1, #FFH
MOV PROTB0, #FFH
; enable read protection on the last four pages only
MOV PROTR, #07FH
PROTR
RP RP RP RP RP RP
0x3FFB 31–28 27–24 23–20 19–16 15–12 11–8
RP
7–4
RP
3–0
; set up a protection key of 0A3H. This command can be
PROTKY
WDOG
0x3FFA LOCK
0x3FF9
PROTECTION KEY
; omitted to use the default protection key of 0xFF
MOV PROTKY, #0A3H
; write the flash key to the FLSHKY register to enable flash
; access. The flash access key is not configurable.
0x3E00
Figure 81. Flash Protection in Page 31
MOV FLSHKY, #3BH
; write flash protection command to the ECON register
MOV ECON, #08H
Rev. PrA | Page 98 of 136
相关PDF资料 |
PDF描述 |
|---|---|
| ADE7752BARWZ-RL | IC ENERGY METERING 3PHASE 24SOIC |
| ADE7755ARSZ | IC ENERGY METERING 1PHASE 24SSOP |
| ADE7757ARNZRL | IC ENERGY METERING 1PHASE 16SOIC |
| ADE7758ARWZRL | IC ENERGY METERING 3PHASE 24SOIC |
| ADE7761AARSZ-RL | IC ENERGY METERING 1PHASE 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7569ASTZF162 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE7569ASTZF16-RL | 功能描述:IC ENERGY METER 1PHASE 64-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7569ASTZF16-RL2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE7751 | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection |
| ADE7751AAN-REF | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection |
发布紧急采购，3分钟左右您将得到回复。