- 您现在的位置：买卖IC网 > Datasheet目录307 > ADE7569ASTZF16 (Analog Devices Inc)IC ENERGY METER MCU 16K 64LQFP Datasheet资料下载
参数资料
| 型号： | ADE7569ASTZF16 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 54/136页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER MCU 16K 64LQFP |
| 标准包装： | 1 |
| 输入阻抗： | * |
| 测量误差： | * |
| 电压 - 高输入/输出： | * |
| 电压 - 低输入/输出： | * |
| 电流 - 电源： | * |
| 电源电压： | * |
| 测量仪表类型： | * |
| 工作温度： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页
ADE7566/ADE7569
Watt Absolute Accumulation Mode
The ADE7566/ADE7569 are placed in watt absolute accumula-
tion mode by setting the ABSAM bit in the ACCMODE Register
(0x0F). In this mode, the energy accumulation is done using the
absolute active power, ignoring any occurrence of power below
the no-load threshold (see Figure 55). The CF pulse also reflects
this accumulation method when in this mode. The default
setting for this mode is off. Detection of the transitions in the
direction of power flow, and detection of no-load threshold are
active in this mode.
ACTIVE ENERGY
NO-LOAD
THRESHOLD
ACTIVE POWER
NO-LOAD
THRESHOLD
APSIGN FLAG
Preliminary Technical Data
behavior is consistent with the setting of the active energy
accumulation mode in the ACCMODE Register (0x0F). The
pulse output is active low and should be preferably connected to
an LED as shown in Figure 66.
Line Cycle Active Energy Accumulation Mode
In line cycle active energy accumulation mode, the energy accumu-
lation of the ADE7566/ADE7569 can be synchronized to the
voltage channel zero crossing so that active energy can be
accumulated over an integral number of half-line cycles. The
advantage of summing the active energy over an integer number
of line cycles is that the sinusoidal component in the active energy
is reduced to 0. This eliminates any ripple in the energy calculation.
Energy is calculated more accurately and more quickly because
the integration period can be shortened. By using this mode,
the energy calibration can be greatly simplified, and the time
required to calibrate the meter can be significantly reduced.
In the line cycle active energy accumulation mode, the
ADE7566/ADE7569 accumulate the active power signal in the
LWATTHR register for an integral number of line cycles, as shown
in Figure 56. The number of half-line cycles is specified in the
LINCYC register.
The ADE7566/ADE7569 can accumulate active power for up to
65,535 half-line cycles. Because the active power is integrated
on an integral number of line cycles, the CYCEND flag in the
Interrupt Status Register 3 SFR (MIRQSTH, 0xDE) is set at the
end of an active energy accumulation line cycle. If the CYCEND
APNOLOAD
POS
NEG
POS
APNOLOAD
enable bit in the Interrupt Enable Register 3 SFR (MIRQENH,
INTERRUPT STATUS REGISTERS
Figure 55. Energy Accumulation in Absolute Accumulation Mode
Active Energy Pulse Output
All of the ADE7566/ADE7569 circuitry has a pulse output whose
frequency is proportional to active power (see the Active Power
Calculation section). This pulse frequency output uses the
calibrated signal from the WGAIN register output, and its
TO
DIGITAL-TO-FREQUENCY
CONVERTER
WGAIN[11:0]
0xDB) is set, the 8052 core has a pending ADE interrupt. The
ADE interrupt stays active until the CYCEND status bit is
cleared (see the Energy Measurement Interrupts section).
Another calibration cycle starts as soon as the CYCEND flag is
set. If the LWATTHR register is not read before a new CYCEND
flag is set, the LWATTHR register is overwritten by a new value.
OUTPUT
FROM
LPF2
%
+
+
48
0
WATTOS[15:0]
WDIV[7:0]
FROM VOLTAGE
CHANNEL
ADC
LPF1
ZERO-CROSSING
DETECTION
CALIBRATION
CONTROL
23
LWATTHR [23:0]
0
ACCUMULATE
ACTIVE ENERGY IN
INTERNAL REGISTER
AND UPDATE THE
LWATTHR REGISTER
AT THE END OF LINCYC
HALF LINE CYCLES
LINCYC [15:0]
Figure 56. Line Cycle Active Energy Accumulation
Rev. PrA | Page 54 of 136
相关PDF资料 |
PDF描述 |
|---|---|
| ADE7752BARWZ-RL | IC ENERGY METERING 3PHASE 24SOIC |
| ADE7755ARSZ | IC ENERGY METERING 1PHASE 24SSOP |
| ADE7757ARNZRL | IC ENERGY METERING 1PHASE 16SOIC |
| ADE7758ARWZRL | IC ENERGY METERING 3PHASE 24SOIC |
| ADE7761AARSZ-RL | IC ENERGY METERING 1PHASE 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7569ASTZF162 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE7569ASTZF16-RL | 功能描述:IC ENERGY METER 1PHASE 64-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7569ASTZF16-RL2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE7751 | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection |
| ADE7751AAN-REF | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection |
发布紧急采购，3分钟左右您将得到回复。