- 您现在的位置：买卖IC网 > PDF目录69323 > RN80532KC0412M (INTEL CORP) 2000 MHz, MICROPROCESSOR, CPGA603 PDF资料下载
参数资料
| 型号： | RN80532KC0412M |
| 厂商： | INTEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 2000 MHz, MICROPROCESSOR, CPGA603 |
| 封装： | Interposer, Micro, PGA-603 |
| 文件页数： | 30/132页 |
| 文件大小： | 2316K |
| 代理商： | RN80532KC0412M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页
Intel Xeon Processor MP with up to 2MB L3 Cache
9-27
NOTES:
1. Intel Xeon processors only support BR0# and BR1#. However, the Intel Xeon processors must terminate
BR2# and BR3# to the processor VCC..
§
THERMTRIP#
O
Assertion of THERMTRIP# (Thermal Trip) indicates the processor junction
temperature has reached a level where permanent silicon damage may occur.
Measurement of the temperature is accomplished through an internal thermal
sensor which is configured to trip at approximately 135°C. Upon assertion of
THERMTRIP#, the processor will shut off its internal clocks (thus halting program
execution) in an attempt to reduce the processor junction temperature. To protect
the processor, its core voltage (Vcc) must be removed following the assertion of
sequence and timing requirements.
Once activated, THERMTRIP# remains latched until RESET# is asserted. While
the assertion of the RESET# signal will de-assert THERMTRIP#, if the processor’s
junction temperature remains at or above the trip level, THERMTRIP# will again be
asserted.
This signal does not have on-die termination and must be terminated at the end
agent. See the appropriate platform design guideline for additional information.
TMS
I
TMS (Test Mode Select) is a JTAG specification support signal used by debug
tools.
This signal does not have on-die termination and must be terminated at the end
agent. See the appropriate platform design guideline for additional information.
TRDY#
I
TRDY# (Target Ready) is asserted by the target to indicate that it is ready to receive
a write or implicit writeback data transfer. TRDY# must connect the appropriate pins
of all system bus agents.
TRST#
I
TRST# (Test Reset) resets the Test Access Port (TAP) logic. TRST# must be driven
low during power on Reset. See the appropriate platform design guideline for
additional information.
VCCA
I
VCCA provides isolated power for the analog portion of the internal PLL’s. Use a
discrete RLC filter to provide clean power. Use the filter defined in Section 2.5 to
provide clean power to the PLL. The tolerance and total ESR for the filter is
important. Refer to the appropriate platform design guidelines for complete
implementation details.
VCCIOPLL
I
VCCIOPLL provides isolated power for digital portion of the internal PLL’s. Follow the
guidelines for VCCA (Section 2.5). Refer to the appropriate platform design
guidelines for complete implementation details.
VCCSENSE
VSSSENSE
O
The Vccsense and Vsssense pins are the points for which processor minimum and
maximum voltage requirements are specified. Uniprocessor designs may utilize
these pins for voltage sensing for the processor's voltage regulator. However, multi-
processor designs must not connect these pins to sense logic, but rather utilize
them for power delivery validation
.
VID[4:0]
O
VID[4:0] (Voltage ID) pins can be used to support automatic selection of power
supply voltages (VCC). Unlike previous generations of processors, these are logic
signals and are driven by the Intel Xeon processor MP on the 0.13 micron process
processor. Hence the voltage supply for these pins (SM_Vcc) must be valid before
the VRM supplying Vcc to the processor is enabled (see Figure ). Conversely, the
VRM output must be disabled prior to the voltage supply for these pins becomes
invalid. The VID pins are needed to support processor voltage specification
variations. See Table 4 for definitions of these pins. The power supply must supply
the voltage that is requested by these pins, or disable itself.
VSSA
I
VSSA provides an isolated, internal ground for internal PLL’s. Do not connect
directly to ground. This pin is to be connected to VCCA and VCCIOPLL through a
appropriate platform design guidelines for complete implementation details.
Table 52. Signal Definitions (Sheet 9 of 9)
Name
Type
Description
相关PDF资料 |
PDF描述 |
|---|---|
| RN80532KC041512 | 32-BIT, 2000 MHz, MICROPROCESSOR, CPGA603 |
| RP0352 | GRAPHICS PROCESSOR, PQFP80 |
| RP65C02G-06 | 8-BIT, 6 MHz, MICROPROCESSOR, PDIP40 |
| RPIXP2800BC | 32-BIT, 650 MHz, RISC PROCESSOR, PBGA1356 |
| RPIXP2850BB | 32-BIT, 1400 MHz, RISC PROCESSOR, PBGA1356 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RN80532KC041512 | 制造商:Intel 功能描述:TRAY XEON 2.0GHZ 400MZH FSB - Trays 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| RN80532KC041512 SL5Z9 | 制造商:Intel 功能描述:MPU XEON 0.13UM 2GHZ 603-PIN UFCBGA - Trays |
| RN80532KC041512 SL6EM | 制造商:Intel 功能描述:MPU XEON 0.13UM 2GHZ 603-PIN UFCBGA - Trays |
| RN80532KC041512S L5Z9 | 制造商:Intel 功能描述:MPU Xeon? Processor 0.13um 2GHz 603-Pin uFCBGA |
| RN80532KC041512S L6W6 | 制造商:Intel 功能描述:MPU Xeon? Processor 0.13um 2GHz 603-Pin uFCBGA |
发布紧急采购，3分钟左右您将得到回复。