参数资料
型号: MT42L64M32D1KL-25 IT:A
厂商: Micron Technology Inc
文件页数: 74/164页
文件大小: 0K
描述: IC DDR2 SDRAM 2GBIT 168FBGA
标准包装: 1,000
格式 - 存储器: RAM
存储器类型: 移动 LPDDR2 SDRAM
存储容量: 2G(64M x 32)
速度: 400MHz
接口: 并联
电源电压: 1.14 V ~ 1.3 V
工作温度: -25°C ~ 85°C
封装/外壳: 168-WFBGA
供应商设备封装: 168-FBGA(12x12)
包装: 散装
2Gb: x16, x32 Mobile LPDDR2 SDRAM S4
REFRESH Command
Table 43: PRECHARGE and Auto Precharge Clarification (Continued)
From
Command
To Command
Minimum Delay Between Commands
Unit
Notes
WRITE w/AP PRECHARGE to same bank as WRITE w/AP
WL + BL/2 + RU( t WR/ t CK) + 1
CLK
1, 2
PRECHARGE ALL
WL + BL/2 +
RU( t WR/ t CK)
+1
CLK
1
ACTIVATE to same bank as WRITE w/AP
WL + BL/2 +
RU( t WR/ t CK)
+1+
RU( t RPpb/ t CK)
CLK
1
WRITE or WRITE w/AP (same bank)
WRITE or WRITE w/AP (different bank)
READ or READ w/AP (same bank)
Illegal
BL/2
Illegal
CLK
CLK
CLK
3
3
3
READ or READ w/AP (different bank)
PRECHARGE PRECHARGE to same bank as PRECHARGE
PRECHARGE ALL
PRECHARGE PRECHARGE
ALL
PRECHARGE ALL
WL + BL/2 +
1
1
1
1
RU( t WTR/ t CK)
+1
CLK
CLK
CLK
CLK
CLK
3
1
1
1
1
Notes:
1. For a given bank, the PRECHARGE period should be counted from the latest PRECHARGE
command—either a one-bank PRECHARGE or PRECHARGE ALL—issued to that bank.
The PRECHARGE period is satisfied after t RP, depending on the latest PRECHARGE com-
mand issued to that bank.
2. Any command issued during the specified minimum delay time is illegal.
3. After READ with auto precharge, seamless READ operations to different banks are sup-
ported. After WRITE with auto precharge, seamless WRITE operations to different banks
are supported. READ with auto precharge and WRITE with auto precharge must not be
interrupted or truncated.
REFRESH Command
The REFRESH command is initiated with CS# LOW, CA0 LOW, CA1 LOW, and CA2 HIGH
at the rising edge of the clock. Per-bank REFRESH is initiated with CA3 LOW at the ris-
ing edge of the clock. All-bank REFRESH is initiated with CA3 HIGH at the rising edge of
the clock. Per-bank REFRESH is only supported in devices with eight banks.
A per-bank REFRESH command (REFpb) performs a per-bank REFRESH operation to
the bank scheduled by the bank counter in the memory device. The bank sequence for
per-bank REFRESH is fixed to be a sequential round-robin: 0-1-2-3-4-5-6-7-0-1-.... The
bank count is synchronized between the controller and the SDRAM by resetting the
bank count to zero. Synchronization can occur upon issuing a RESET command or at
every exit from self refresh. Bank addressing for the per-bank REFRESH count is the
same as established for the single-bank PRECHARGE command (see Table 42
(page 69)).
A bank must be idle before it can be refreshed. The controller must track the bank being
refreshed by the per-bank REFRESH command.
The REFpb command must not be issued to the device until the following conditions
have been met:
? t RFCab has been satisfied after the prior REFab command
? t RFCpb has been satisfied after the prior REFpb command
? t RP has been satisfied after the prior PRECHARGE command to that bank
PDF: 09005aef83f3f2eb
2gb_mobile_lpddr2_s4_g69a.pdf – Rev. N 3/12 EN
74
Micron Technology, Inc. reserves the right to change products or specifications without notice.
2010 Micron Technology, Inc. All rights reserved.
相关PDF资料
PDF描述
IDT71V67803S133BQG8 IC SRAM 9MBIT 133MHZ 165FBGA
IDT71V65803S150PFG IC SRAM 9MBIT 150MHZ 100TQFP
IDT71V67903S85BQI8 IC SRAM 9MBIT 85NS 165FBGA
IDT71V67903S80BQI8 IC SRAM 9MBIT 80NS 165FBGA
IDT71V67903S75BQI8 IC SRAM 9MBIT 75NS 165FBGA
相关代理商/技术参数
参数描述