- 您现在的位置：买卖IC网 > PDF目录385639 > MT48V4M32LFFC (Micron Technology, Inc.) SYNCHRONOUS DRAM PDF资料下载
参数资料
| 型号： | MT48V4M32LFFC |
| 厂商： | Micron Technology, Inc. |
| 英文描述： | SYNCHRONOUS DRAM |
| 中文描述： | 同步DRAM |
| 文件页数： | 18/61页 |
| 文件大小： | 1400K |
| 代理商： | MT48V4M32LFFC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页
18
128Mb: x16, x32 Mobile SDRAM
MobileY95W_3V_F.p65 – Rev. F; Pub. 9/02
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2002, Micron Technology, Inc.
128Mb: x16, x32
MOBILE SDRAM
ADVANCE
Upon completion of a burst, assuming no other com-
mands have been initiated, the DQs will go High-Z. A full-
page burst will continue until terminated. (At the end of
the page, it will wrap to column 0 and continue.)
Data from any READ burst may be truncated with a
subsequent READ command, and data from a fixed-length
READ burst may be immediately followed by data from a
READ command. In either case, a continuous flow of data
can be maintained. The first data element from the new
burst follows either the last element of a completed burst
or the last desired data element of a longer burst that is
being truncated. The new READ command should be
issued
x
cycles before the clock edge at which the last
desired data element is valid, where
x
equals the CAS
latency minus one.
READs
READ bursts are initiated with a READ command, as
shown in Figure 5.
The starting column and bank addresses are provided
with the READ command, and auto precharge is either
enabled or disabled for that burst access. If auto precharge
is enabled, the row being accessed is precharged at the
completion of the burst. For the generic READ com-
mands used in the following illustrations, auto precharge
is disabled.
During READ bursts, the valid data-out element from
the starting column address will be available following
the CAS latency after the READ command. Each subse-
quent data-out element will be valid by the next positive
clock edge. Figure 6 shows general timing for each pos-
sible CAS latency setting.
Figure 5
READ Command
Figure 6
CAS Latency
DON’T CARE
CS#
WE#
CAS#
RAS#
CKE
CLK
COLUMN
A0-A8
A10
BA0,1
HIGH
ENABLE AUTO PRECHARGE
DISABLE AUTO PRECHARGE
ABANK
A9, A11
CLK
DQ
T2
T1
T3
T0
CAS Latency = 3
LZ
D
OUT
tOH
t
COMMAND
NOP
READ
tAC
NOP
T4
NOP
DON’T CARE
UNDEFINED
CLK
DQ
T2
T1
T0
CAS Latency = 1
LZ
D
OUT
tOH
t
COMMAND
NOP
READ
tAC
CLK
DQ
T2
T1
T3
T0
CAS Latency = 2
LZ
D
OUT
tOH
t
COMMAND
NOP
READ
tAC
NOP
相关PDF资料 |
PDF描述 |
|---|---|
| MT49H16M16 | THERMISTOR PTC 100OHM 110DEG RAD |
| MT49H16M16FM | REDUCED LATENCY DRAM RLDRAM |
| MT49H8M32 | THERMISTOR PTC 100OHM 120DEG RAD |
| MT49H8M32FM | REDUCED LATENCY DRAM RLDRAM |
| MT4C1M16E5DJ-6 | EDO DRAM |
相关代理商/技术参数 |
参数描述 |
|---|
发布紧急采购，3分钟左右您将得到回复。