- 您现在的位置：买卖IC网 > Datasheet目录441 > HSP50216KIZ (Intersil)IC DOWNCONVERTER DGTL 4CH 196BGA Datasheet资料下载
参数资料
| 型号： | HSP50216KIZ |
| 厂商： | Intersil |
| 文件页数： | 15/58页 |
| 文件大小： | 0K |
| 描述： | IC DOWNCONVERTER DGTL 4CH 196BGA |
| 标准包装： | 1 |
| 功能： | 降频器 |
| RF 型： | W-CDMA |
| 封装/外壳： | 196-LFBGA |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
HSP50216
Filter Example #4 will be used to demonstrate this capability.
Symbol rate of 4.096 MSym. The desired output sample rate
is 8.192MSPS. Arrange the four back end sections as four
filters operating on the same CIC output at a rate of
65.536MHz/4=16.384MHz, where the factor of 4 is the CIC
decimation we have chosen.
Each channel computes the same sequence, offset by one
output sample from the previous sample (see IWA = *00Bh).
Each channel decimates down to 2.048M and then the
channels are multiplexed together in the output formatter to
get the desired 8.192MSPS. The input sample rate to the
final filter of each channel must meet Nyquist requirements
for the final output to assure that no information is lost due to
aliasing.
SAMPLE FILTER #4 PROGRAM
part (except via the μ P interface), so polyphase filter using
multiple parts would typically usually use a fixed gain.
The filter sequencer is programmed via an instruction RAM
and several control registers. These are described below.
Instruction RAMs
The filter compute engine is controlled by a simple
sequencer supporting up to 32 steps. Each step can be a
filter or one of four sequence flow instructions - wait, jump
(conditional or unconditional), load loop counter, or NOP.
There are 128 bits per instruction word with each word
consisting of condition code selects, FIR parameters and
data routing controls. Not all of the instruction word bits are
used for all instruction types. The actual sequencer
instruction is only 9 bits. The rest of the bits are used for filter
parameters or for the loop counter preload. Each sequence
step is loaded in four 32-bit writes. The mapping of the bit
STEP
0
1
2
INSTRUCTION
Wait for enough input samples (8 in this case)
FIR
type = even symmetry
44 taps
decimate by 8
compute one output
memory block size 64
memory block start at 0
coefficient block start at 64
step size 1
output to AGC
offset memory read pointers by 0, -2, -4, -6
Jump, Unconditional, to 0
fields for the instruction types is shown in the instruction bit
field table that follows. These FIR instruction words can be
generated using software tools provided with the HSP50216
evaluation board.
When the filter is reset, the instruction pointer is set to 31
(the last instruction step). The read and write pointers are
initialized on reset, so a reset must be done when the
channel is initialized or restarted.
A fixed offset can be added to the starting read address of
one of the filters in the program. This function is provided to
offset the data reads of the filters in a polyphase filter bank --
all filters in the bank will write the same data to the same
RAM location. To offset the computations the RAM read
The number of FIR taps available for these requirements is
calculated as follows:
65536/2048 = 32 clocks
minus (8 writes + 1 wait + 1 jump = 10 clocks)
= 22 clocks
Therefore, the number of taps available is:
22 x 2 = 44 taps.
Multiplexing the four outputs gives a final output sample rate
of 8.192MSPS.
The impulse response is 44 taps at 16.384M or 22 output
samples (11 symbols at 4.096M).
The AGC loop filter output of channel 4 can be routed to
control the forward AGC gain control of all four channels.
This assures that the gains of the four back end sections are
the same. The gain error, however, is only computed from
every fourth output sample.
The back end processing sections of two or more HSP50216s
can be combined using the same polyphase approach, but
the AGC gain from one part cannot be shared with another
15
address is offset. See IWA = *00Bh for details.
The instruction word bits (127:0) are assigned to memory
words as follows:
31:0 to destination C C C C 0 0 0 1 0 x x x x x 0 0
63:32 to destination C C C C 0 0 0 1 0 x x x x x 0 1
95:64 to destination C C C C 0 0 0 1 0 x x x x x 1 0
127:96 to destination C C C C 0 0 0 1 0 x x x x x 1 1
where CCCC is the channel number and xxxxx is the
instruction sequence step number (0 - 31 decimal). Note the
μ PHold bit in the filter compute engine control register (IWA
= *00Ah) must be set for the microprocessor to read from or
write to the instruction or coefficient RAMs.
FN4557.6
August 17, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| HSP50415VIZ | IC MODULATOR PROGRAMABLE 100MQFP |
| HSSLS-CALBL-013 | HEATSINK 48W SPOT OSRAM PREVALED |
| HSSLS-CALCL-005 | HEATSINK 21W SPOT PHILIPS SLM |
| HSSLS-CALCL-013 | HEATSINK 48W DOWNLIGHT 140 |
| HTA-300-S | SENSOR CURR 300A -/+15V MOD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HSP50306 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Digital QPSK Demodulator |
| HSP50306 WAF | 制造商:Intersil Corporation 功能描述: |
| HSP50306_04 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Digital QPSK Demodulator |
| HSP50306SC-25 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HSP50306SC-2596 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Digital QPSK Demodulator |
发布紧急采购，3分钟左右您将得到回复。