参数资料
型号: IDT88P8341BHGI
厂商: IDT, Integrated Device Technology Inc
文件页数: 35/96页
文件大小: 0K
描述: IC SPI3-SPI4 EXCHANGE 820-PBGA
标准包装: 24
系列: *
其它名称: 88P8341BHGI
40
IDT88P8341 SPI EXCHANGE SPI-3 TO SPI-4
INDUSTRIALTEMPERATURERANGE
APRIL 10, 2006
8. OPERATION GUIDE
8.1 Hardware operation
8.1.1 System reset
There are two methods for resetting the device: hardware reset & software
reset. During reset the output clocks are not toggled.
Hardware reset
The RESETB input requires an active low pulse to reset the internal logic.
Software reset
The software reset is triggered by setting to 1 the SW_RESET field in direct
register Software Reset Register (p.50). The response to a software reset is
identical to a hardware rest except that software reset does not change the
N_OCLK[3:0] fields in the Clock Generator Control Register (p.74), so it does
not impact the clock generators. The SW_RESET field is self-clear to 0 after the
device initialized itself.After software reset the external microprocessor should
have delay of at least 1ms before accessing the device, and then.After the 1ms
delay, the user should poll the INIT_DONE field in the Software Reset Register
(p.50), and wait till it is 1. When the INIT_DONE field is 1, the user should
download a boot code from the external microprocessor flash to the device
embedded processor RAM.
8.1.2 Power on sequence
A correct power-on-reset sequence is crucial for the normal behavior of
the device. The power-on-reset sequence includes the following signals:
CLK (REF_CLK or I_DCLK - depends on which of theses pins are selected),
VDDT33, VDDC12 and RESETB. Figure 31, Power-on-Reset Sequence
illustrates the recommended implementation for the power-on-reset sequence
for the device. IDT recommends powering up the VDD33 power supply first,
and the VDDC18 power supply last. The power supplies can be also powered
up in the same time. There is no requirement for the minimum or maximum
delay between the power-up of the power supplies. The power supplies
should be powered off in the revers order. The power ramp should not be fast
than 100us, but also not too slow.
When the power supplies are powered up, the RESETB signal should be
at low level. During power-on-reset, after the VDDT33, VDDC18, CLK
(REF_CLK or I_DCLK - depends on which of theses pins are selected) and
the configuration signals are stable, the RESETB signal should remain at a low
level at least 10ms (symbol “T1”) to reset the internal logic. After the RESETB
pulse ends, the device starts generating the SPI-4 / SPI-3 external output
clocks & the MCLK internal clock.
After the RESETB pulse ends, a delay of 1ms should be added (symbols
“T2”) before accessing the device for initialization and configuration. This
allows the internal logic to be stable. During T2 (at least 1ms delay) the device
performs internal memories initialization.
After T2, the user should poll the INIT_DONE field in the in the Software
Reset Register (p.50), and wait till it is 1. When the INIT_DONE field is 1, the
user should download a boot code from the external microprocessor flash to
the device embedded processor RAM.
T1
CLK
VDDT33
RESETB
T2
VDDC18
6372 drw28a
Figure 31. Power-on-Reset Sequence
8.1.3 Clock domains
The chip has several clock domains. The related registers can not be
configured without each clock. It is necessary to supply the clocks that are
pertinenttotheregistersbeinginitializedfortheinitializationtosucceed.Inorder
toaccessthemicroprocessorinterface,MCLKmustbeactive,eitherbyselecting
andprovidingastableREF_CLKinput,orbyselectingandensuringthatastable
clock is always present on the I_DCLK input. The selection of either the
REF_CLK or the I_DCLK clock inputs is described in Table 14 CK_SEL[3:0]
input pin decoding.
8.2 Software operation
8.2.1 Chip configuration sequence
Forproperdeviceoperation,itisimportanttoinitializetheIDT88P8341inthe
correct sequence following reset. This sequence is outlined in the following
paragraphs.
1) Reset the IDT88P8341 chip. After reset, the chip will perform auto
initialization.Waitforthechipinitializationtocomplete.TheINIT_DONEflagwill
go high when initialization has been completed.
相关PDF资料
PDF描述
LFEC15E-4FN484C IC FPGA 10.2KLUTS 288I/O 484-BGA
IDT72V51446L7-5BBI IC FLOW CTRL MULTI QUEUE 256-BGA
LFEC15E-4F484C IC FPGA 10.2KLUTS 288I/O 484-BGA
LT3022IMSE-1.8#TRPBF IC REG LDO 1.8V 1A 16-MSOP
LT3022IMSE-1.5#TRPBF IC REG LDO 1.5V 1A 16-MSOP
相关代理商/技术参数
参数描述
IDT88P8341BHI 功能描述:IC SPI3-SPI4 EXCHANGE 820-PBGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA(27x27) 包装:散装
IDT88P8342BHGI 功能描述:IC SPI3-SPI4 EXCHANGE 820-PBGA RoHS:是 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA(27x27) 包装:散装
IDT88P8342BHI 功能描述:IC SPI3-SPI4 EXCHANGE 820-PBGA RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA(27x27) 包装:散装
IDT88P8344 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:SPI EXCHANGE 4 x SPI-3 TO SPI-4 Issue 1.0
IDT88P8344BHGI 功能描述:IC SPI3-SPI4 EXCHANGE 820-PBGA RoHS:是 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA(27x27) 包装:散装