- 您现在的位置：买卖IC网 > PDF目录11210 > ADUC7061BCPZ32-RL (Analog Devices Inc)IC MCU 16/32BIT 32KB 32LFCSP PDF资料下载
参数资料
| 型号： | ADUC7061BCPZ32-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 102/108页 |
| 文件大小： | 0K |
| 描述： | IC MCU 16/32BIT 32KB 32LFCSP |
| 产品变化通告： | ADuC7060/1 Idd Specification Change 01/Feb/2010 |
| 设计资源： | USB Based Temperature Monitor Using ADuC7061 and an External RTD (CN0075) 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) |
| 标准包装： | 5,000 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 10MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | POR，PWM，温度传感器，WDT |
| 输入/输出数： | 8 |
| 程序存储器容量： | 32KB（16K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 32 |
| 电压 - 电源 (Vcc/Vdd)： | 2.375 V ~ 2.625 V |
| 数据转换器： | A/D 5x24b，8x24b，D/A 1x14b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页当前第102页第103页第104页第105页第106页第107页第108页
Data Sheet
ADuC7060/ADuC7061
Rev. D | Page 93 of 108
I2C Slave Status, I2CSSTA, Register
Name:
I2CSSTA
Address:
0xFFFF092C
Default value:
0x0000
Access:
Read and write
Function:
This 16-bit MMR is the I2C status register in slave mode.
Table 105. I2CSSTA MMR Bit Designations
Bit
Name
Description
15
Reserved bit.
14
I2CSTA
This bit is set to 1 if a start condition followed by a matching address is detected, a start byte (0x01) is received, or
general calls are enabled and a general call code of 0x00 is received.
This bit is cleared on receiving a stop condition
13
I2CREPS
This bit is set to 1 if a repeated start condition is detected.
This bit is cleared on receiving a stop condition.
12:11
I2CID[1:0]
I2C address matching register. These bits indicate which I2CIDx register matches the received address.
[00] = received address matches I2CID0.
[01] = received address matches I2CID1.
[10] = received address matches I2CID2.
[11] = received address matches I2CID3.
10
I2CSS
I2C stop condition after start detected bit.
This bit is set to 1 when a stop condition is detected after a previous start and matching address. When the
I2CSSENI bit in I2CSCON is set, an interrupt is generated.
This bit is cleared by reading this register.
9:8
I2CGCID[1:0]
I2C general call ID bits.
[00] = no general call received.
[01] = general call reset and program address.
[10] = general program address.
[11] = general call matching alternative ID.
Note that these bits are not cleared by a general call reset command.
Clear these bits by writing a 1 to the I2CGCCLR bit in I2CSCON.
7
I2CGC
I2C general call status bit.
This bit is set to 1 if the slave receives a general call command of any type. If the command received was a reset
command, then all registers return to their default states. If the command received was a hardware general call,
the receive FIFO holds the second byte of the command, and this can be compared with the I2CALT register.
Clear this bit by writing a 1 to the I2CGCCLR bit in I2CSCON.
6
I2CSBUSY
I2C slave busy status bit.
Set to 1 when the slave receives a start condition.
Cleared by hardware if the received address does not match any of the I2CIDx registers, the slave device receives
a stop condition, or a repeated start address does not match any of the I2CIDx registers.
5
I2CSNA
I2C slave no acknowledge data bit.
This bit is set to 1 when the slave responds to a bus address with a no acknowledge. This bit is asserted under the
following conditions: if a no acknowledge was returned because there was no data in the transmit FIFO or if the
I2CNACKEN bit was set in the I2CSCON register.
This bit is cleared in all other conditions.
4
I2CSRxFO
Slave receive FIFO overflow.
This bit is set to 1 when a byte is written to the receive FIFO when it is already full.
This bit is cleared in all other conditions.
3
I2CSRXQ
I2C slave receive request bit.
This bit is set to 1 when the receive FIFO of the slave is not empty. This bit causes an interrupt to occur if the
I2CSRXENI bit in I2CSCON is set.
The receive FIFO must be read or flushed to clear this bit.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B2L-IW-F4 | CONVERTER MOD DC/DC 28V 100W |
| ATMEGA8535L-8JU | MCU AVR 8K ISP FLASH MEM 44-PLCC |
| VI-B2L-IW-F3 | CONVERTER MOD DC/DC 28V 100W |
| ATMEGA8535L-8PU | IC AVR MCU 8K 8MHZ 3V 40DIP |
| VI-B2L-IW-F2 | CONVERTER MOD DC/DC 28V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC70SMARTLINKRL7 | 制造商:Analog Devices 功能描述: |
| ADUC70TEL | 制造商:Analog Devices 功能描述:FLASH ARM +5-CH 12BIT ADC - Trays |
| ADUC70TEL-RL7 | 制造商:Analog Devices 功能描述: |
| ADUC7120BBCZ | 制造商:Analog Devices 功能描述:- Rail/Tube |
| ADUC7120BBCZ-RL | 制造商:Analog Devices 功能描述:- Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。