- 您现在的位置：买卖IC网 > PDF目录11210 > ADUC7061BCPZ32-RL (Analog Devices Inc)IC MCU 16/32BIT 32KB 32LFCSP PDF资料下载
参数资料
| 型号： | ADUC7061BCPZ32-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 78/108页 |
| 文件大小： | 0K |
| 描述： | IC MCU 16/32BIT 32KB 32LFCSP |
| 产品变化通告： | ADuC7060/1 Idd Specification Change 01/Feb/2010 |
| 设计资源： | USB Based Temperature Monitor Using ADuC7061 and an External RTD (CN0075) 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) |
| 标准包装： | 5,000 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 10MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | POR，PWM，温度传感器，WDT |
| 输入/输出数： | 8 |
| 程序存储器容量： | 32KB（16K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 32 |
| 电压 - 电源 (Vcc/Vdd)： | 2.375 V ~ 2.625 V |
| 数据转换器： | A/D 5x24b，8x24b，D/A 1x14b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页当前第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页
Data Sheet
ADuC7060/ADuC7061
Rev. D | Page 71 of 108
TIMER2 OR WATCHDOG TIMER
Timer2 has two modes of operation, normal mode and
watchdog mode. The watchdog timer is used to recover
from an illegal software state. When enabled, it requires
periodic servicing to prevent it from forcing a reset of the
processor.
Timer2 reloads the value from T2LD either when Timer2
overflows or immediately when T2CLRI is written.
Normal Mode
Timer2 in normal mode is identical to Timer0 in the 16-bit
mode of operation, except for the clock source. The clock
source is the low power, 32.768 kHz oscillator scalable by a
factor of 1, 16, or 256.
Watchdog Mode
Watchdog mode is entered by setting T2CON[Bit 5]. Timer2
decrements from the timeout value present in the T2LD register
until zero. The maximum timeout is 512 seconds, using a
maximum prescaler/256 and full scale in T2LD.
User software should not configure a timeout period of less
than 30 ms. This is to avoid any conflict with Flash/EE memory
page erase cycles that require 20 ms to complete a single page
erase cycle and kernel execution.
If T2VAL reaches 0, a reset or an interrupt occurs, depending
on T2CON[1]. To avoid a reset or an interrupt event, any value
must be written to T2CLRI before T2VAL reaches zero. This
reloads the counter with T2LD and begins a new timeout period.
When watchdog mode is entered, T2LD and T2CON are
write protected. These two registers cannot be modified until
a power-on reset event resets the watchdog timer. After any
other reset event, the watchdog timer continues to count. To
avoid an infinite loop of watchdog resets, configure the
watchdog timer in the initial lines of user code. User software
should configure a minimum timeout period of 30 ms only.
Timer2 halts automatically during JTAG debug access and only
recommences counting after JTAG relinquishes control of the
ARM7 core. By default, Timer2 continues to count during
power-down. To disable this, set Bit 0 in T2CON. It is
recommended that the default value be used, that is, that the
watchdog timer continues to count during power-down.
Timer2 Interface
The Timer2 interface consists of four MMRs.
T2CON is the configuration MMR, described in (Table 82).
T2LD and T2VAL are 16-bit registers (Bit 0 to Bit 15) and
hold 16-bit, unsigned integers. T2VAL is read only.
T2CLRI is an 8-bit register. Writing any value to this
register clears the Timer2 interrupt in normal mode or
resets a new timeout period in watchdog mode.
Timer2 Load Register
Name:
T2LD
Address:
0xFFFF0360
Default value:
0x3BF8
Access:
Read and write
Function:
This 16-bit MMR holds the Timer2
reload value.
Timer2 Clear Register
Name:
T2CLRI
Address:
0xFFFF036C
Access:
Write only
Function:
This 8-bit, write-only MMR is written (with
any value) by user code to refresh (reload)
Timer2 in watchdog mode to prevent a
watchdog timer reset event.
Timer2 Value Register
Name:
T2VAL
Address:
0xFFFF0364
Default value:
0x3BF8
Access:
Read only
Function:
This 16-bit, read-only MMR holds the
current Timer2 count value.
PRESCALER
1, 16, 256
TIMER2 IRQ
WATCHDOG RESET
16-BIT
UP/DOWN COUNTER
32.768kHz
16-BIT LOAD
TIMER2
VALUE
07079-
019
Figure 25. Timer2 Block Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B2L-IW-F4 | CONVERTER MOD DC/DC 28V 100W |
| ATMEGA8535L-8JU | MCU AVR 8K ISP FLASH MEM 44-PLCC |
| VI-B2L-IW-F3 | CONVERTER MOD DC/DC 28V 100W |
| ATMEGA8535L-8PU | IC AVR MCU 8K 8MHZ 3V 40DIP |
| VI-B2L-IW-F2 | CONVERTER MOD DC/DC 28V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC70SMARTLINKRL7 | 制造商:Analog Devices 功能描述: |
| ADUC70TEL | 制造商:Analog Devices 功能描述:FLASH ARM +5-CH 12BIT ADC - Trays |
| ADUC70TEL-RL7 | 制造商:Analog Devices 功能描述: |
| ADUC7120BBCZ | 制造商:Analog Devices 功能描述:- Rail/Tube |
| ADUC7120BBCZ-RL | 制造商:Analog Devices 功能描述:- Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。