- 您现在的位置：买卖IC网 > PDF目录11720 > PI7C8154BNAE (Pericom)IC PCI-PCI BRIDGE ASYNC 304-PBGA PDF资料下载
参数资料
| 型号： | PI7C8154BNAE |
| 厂商： | Pericom |
| 文件页数： | 6/114页 |
| 文件大小： | 0K |
| 描述： | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
| 标准包装： | 27 |
| 系列： | * |
| 应用： | * |
| 接口： | * |
| 电源电压： | * |
| 封装/外壳： | 304-BBGA |
| 供应商设备封装： | 304-PBGA（31x31） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页
PI7C8154B
ASYNCHRONOUS 2-PORT
PCI-to-PCI BRIDGE
Advance Information
Page 103 of 114
JUNE 2008 REVISION 1.1
Upon activation of the TRST# reset pin, the latched instruction asynchronously changes to the id
code instruction. When the TAP controller moves into the test state other than by reset activation,
the opcode changes as TDI shifts, and becomes active on the falling edge of TCK.
16.2
BOUNDARY SCAN INSTRUCTION SET
The PI7C8154B supports three mandatory boundary-scan instructions (BYPASS, SAMPLE and
EXTEST). Table 16-1 shown below lists the PI7C8154B’s boundary-scan instruction codes.
Table 16-1 TAP PINS
Instruction
/
Requisite
Opcode (binary)
Description
EXTEST
IEEE 1149.1
Required
00000
EXTEST initiates testing of external circuitry, typically board-level
interconnects and off chip circuitry. EXTEST connects the boundary-
scan register between TDI and TDO. When EXTEST is selected, all
output signal pin values are driven by values shifted into the boundary-
scan register and may change only of the falling edge of TCK. Also,
when EXTEST is selected, all system input pin states must be loaded
into the boundary-scan register on the rising-edge of TCK.
SAMPLE
IEEE 1149.1
Required
0001
SAMPLE performs two functions:
A snapshot of the sample instruction is captured on the rising
edge of TCK without interfering with normal operation. The
instruction causes boundary-scan register cells associated with
outputs to sample the value being driven.
On the falling edge of TCK, the data held in the boundary-scan
cells is transferred to the slave register cells. Typically, the slave
latched data is applied to the system outputs via the EXTEST
instruction.
INTSCAN
00010
Enable internal SCAN test
CLAMP
00100
CLAMP instruction allows the state of the signals driven from
component pins to be determined from the boundary-scan register
while the bypass register is selected as the serial path between TDI and
TDO. The signal driven from the component pins will not change
while the CLAMP instruction is selected.
BYPASS
11111
BYPASS instruction selects the one-bit bypass register between TDI
and TDO pins. 0 (binary) is the only instruction that accesses the
bypass register. While this instruction is in effect, all other test data
registers have no effect on system operation. Test data registers with
both test and system functionality performs their system functions
when this instruction is selected.
16.3
TAP TEST DATA REGISTERS
The PI7C8154B contains two test data registers (bypass and boundary-scan). Each test data
register selected by the TAP controller is connected serially between TDI and TDO. TDI is
connected to the test data register’s most significant bit. TDO is connected to the least significant
bit. Data is shifted one bit position within the register towards TDO on each rising edge of TCK.
While any register is selected, data is transferred from TDI to TDO without inversion. The
following sections describe each of the test data registers.
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1025AARQ | IC MONITOR SYS/VOLT 5CH 16QSOP |
| ADUC832BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 31-10 | BNC FRONT MOUNT RECEPT |
| D38999/20JD97SN | CONN RCPT 12POS WALL MNT W/SCKT |
| ADUC848BSZ62-5 | IC FLASH MCU W/16BIT ADC 52MQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PI7C8154BNAE-80 | 功能描述:外围驱动器与原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| PI7C8154BNAI | 制造商:Pericom Semiconductor Corporation 功能描述: |
| PI7C8154BNAIE | 功能描述:外围驱动器与原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| PI7C8154EVB | 功能描述:界面开发工具 64B/66MHz 2 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| PI7C8154NA-33 | 制造商:PERICOM 功能描述: |
发布紧急采购，3分钟左右您将得到回复。