- 您现在的位置：买卖IC网 > PDF目录11720 > PI7C8154BNAE (Pericom)IC PCI-PCI BRIDGE ASYNC 304-PBGA PDF资料下载
参数资料
| 型号： | PI7C8154BNAE |
| 厂商： | Pericom |
| 文件页数： | 66/114页 |
| 文件大小： | 0K |
| 描述： | IC PCI-PCI BRIDGE ASYNC 304-PBGA |
| 标准包装： | 27 |
| 系列： | * |
| 应用： | * |
| 接口： | * |
| 电源电压： | * |
| 封装/外壳： | 304-BBGA |
| 供应商设备封装： | 304-PBGA（31x31） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页当前第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页
PI7C8154B
ASYNCHRONOUS 2-PORT
PCI-to-PCI BRIDGE
Advance Information
Page 55 of 114
JUNE 2008 REVISION 1.1
For upstream transactions, when PI7C8154B detects a read data parity error on the primary bus, the
following events occur:
PI7C8154B asserts P_PERR# 2 cycles following the data transfer, if the primary interface
parity error response bit is set in the command register.
PI7C8154B sets the detected parity error bit in the primary status register.
PI7C8154B sets the data parity detected bit in the primary status register, if the primary
interface parity-error-response bit is set in the command register.
PI7C8154B forwards the bad parity with the data back to the initiator on the secondary bus. If
the data with the bad parity is pre-fetched and is not read by the initiator on the secondary bus,
the data is discarded and the data with bad parity is not returned to the initiator.
PI7C8154B completes the transaction normally.
PI7C8154B returns to the initiator the data and parity that was received from the target. When the
initiator detects a parity error on this read data and is enabled to report it, the initiator asserts
PERR# two cycles after the data transfer occurs. It is assumed that the initiator takes responsibility
for handling a parity error condition; therefore, when PI7C8154B detects PERR# asserted while
returning read data to the initiator, PI7C8154B does not take any further action and completes the
transaction normally.
5.2.3
DELAYED WRITE TRANSACTIONS
When PI7C8154B detects a data parity error during a delayed write transaction, the initiator drives
data and data parity, and the target checks parity and conditionally asserts PERR#.
For delayed write transactions, a parity error can occur at the following times:
During the original delayed write request transaction
When the initiator repeats the delayed write request transaction
When PI7C8154B completes the delayed write transaction to the target
When a delayed write transaction is normally queued, the address, command, address parity, data,
byte enable bits, and data parity are all captured and a target retry is returned to the initiator. When
PI7C8154B detects a parity error on the write data for the initial delayed write request transaction,
the following events occur:
If the parity-error-response bit corresponding to the initiator bus is set, PI7C8154B asserts
TRDY# to the initiator and the transaction is not queued. If multiple data phases are requested,
STOP# is also asserted to cause a target disconnect. Two cycles after the data transfer,
PI7C8154B also asserts PERR#.
If the parity-error-response bit is not set, PI7C8154B returns a target retry. It queues the
transaction as usual. PI7C8154B does not assert PERR#. In this case, the initiator repeats the
transaction.
PI7C8154B sets the detected-parity-error bit in the status register corresponding to the initiator
bus, regardless of the state of the parity-error-response bit.
Note: If parity checking is turned off and data parity errors have occurred for queued or subsequent
delayed write transactions on the initiator bus, it is possible that the initiator’s re-attempts of the
write transaction may not match the original queued delayed write information contained in the
delayed transaction queue. In this case, a master timeout condition may occur, possibly resulting in
a system error (P_SERR# assertion).
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1025AARQ | IC MONITOR SYS/VOLT 5CH 16QSOP |
| ADUC832BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 31-10 | BNC FRONT MOUNT RECEPT |
| D38999/20JD97SN | CONN RCPT 12POS WALL MNT W/SCKT |
| ADUC848BSZ62-5 | IC FLASH MCU W/16BIT ADC 52MQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PI7C8154BNAE-80 | 功能描述:外围驱动器与原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| PI7C8154BNAI | 制造商:Pericom Semiconductor Corporation 功能描述: |
| PI7C8154BNAIE | 功能描述:外围驱动器与原件 - PCI 64B/66MHz 2 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| PI7C8154EVB | 功能描述:界面开发工具 64B/66MHz 2 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| PI7C8154NA-33 | 制造商:PERICOM 功能描述: |
发布紧急采购，3分钟左右您将得到回复。