- 您现在的位置：买卖IC网 > PDF目录262949 > MT46H16M32LFB5-6IT:C 16M X 32 DDR DRAM, PBGA90 PDF资料下载
参数资料
| 型号： | MT46H16M32LFB5-6IT:C |
| 元件分类： | DRAM |
| 英文描述： | 16M X 32 DDR DRAM, PBGA90 |
| 封装： | 13 X 8 MM, GREEN, PLASTIC, VFBGA-90 |
| 文件页数： | 16/95页 |
| 文件大小： | 3228K |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页
Table 11: IDD6 Specifications and Conditions
Notes 1–5, 7, and 12 apply to all the parameters/conditions in this table; VDD/VDDQ = 1.70–1.95V
Parameter/Condition
Symbol
Low Power
Standard
Units
Self refresh
CKE = LOW; tCK = tCK (MIN); Address and control
inputs are stable; Data bus inputs are stable
Full array, 85C
IDD6
TBD
700
μA
Full array, 45C
TBD
390
μA
1/2 array, 85C
TBD
520
μA
1/2 array, 45C
TBD
310
μA
1/4 array, 85C
TBD
430
μA
1/4 array, 45C
TBD
275
μA
1/8 array, 85C
TBD
430
μA
1/8 array, 45C
TBD
275
μA
1/16 array, 85C
TBD
375
μA
1/16 array, 45C
TBD
250
μA
Notes: 1. All voltages referenced to VSS.
2. Tests for IDD characteristics may be conducted at nominal supply voltage levels, but the
related specifications and device operation are guaranteed for the full voltage range
specified.
3. Timing and IDD tests may use a VIL-to-VIH swing of up to 1.5V in the test environment,
but input timing is still referenced to VDDQ/2 (or to the crossing point for CK/CK#). The
output timing reference voltage level is VDDQ/2.
4. IDD is dependent on output loading and cycle rates. Specified values are obtained with
minimum cycle time with the outputs open.
5. IDD specifications are tested after the device is properly initialized and values are aver-
aged at the defined cycle rate.
6. MIN (tRC or tRFC) for IDD measurements is the smallest multiple of tCK that meets the
minimum absolute value for the respective parameter. tRASmax for IDD measurements is
the largest multiple of tCK that meets the maximum absolute value for tRAS.
7. Measurement is taken 500ms after entering into this operating mode to provide settling
time for the tester.
8. VDD must not vary more than 4% if CKE is not active while any bank is active.
9. IDD2N specifies DQ, DQS, and DM to be driven to a valid high or low logic level.
10. CKE must be active (HIGH) during the entire time a REFRESH command is executed.
From the time the AUTO REFRESH command is registered, CKE must be active at each
rising clock edge until tRFC later.
11. This limit is a nominal value and does not result in a fail. CKE is HIGH during REFRESH
command period (tRFC (MIN)) else CKE is LOW (for example, during standby).
12. Values for IDD6 85C are guaranteed for the entire temperature range. All other IDD6 val-
ues are estimated.
13. Typical values at 25C, not a maximum value.
Micron Confidential and Proprietary
Advance
512Mb: x16, x32 Mobile LPDDR SDRAM
Electrical Specifications – IDD Parameters
PDF: 09005aef83dd2b3e
t67m_512mb_mobile_lpddr.pdf - Rev. B 2/10 EN
23
Micron Technology, Inc. reserves the right to change products or specifications without notice.
2009 Micron Technology, Inc. All rights reserved.
相关PDF资料 |
PDF描述 |
|---|---|
| ML1I-65656L-100CB | 32K X 8 STANDARD SRAM, 100 ns, CDIP28 |
| M95160-MB6TP | 2K X 8 SPI BUS SERIAL EEPROM, DSO8 |
| M95160-WMB3T | 2K X 8 SPI BUS SERIAL EEPROM, DSO8 |
| MT45W2MV16BAFB-601WT | 2M X 16 PSEUDO STATIC RAM, 60 ns, PBGA54 |
| MT45W2MV16BAFB-706LIT | 2M X 16 PSEUDO STATIC RAM, 70 ns, PBGA54 |
相关代理商/技术参数 |
参数描述 |
|---|
发布紧急采购，3分钟左右您将得到回复。