参数资料
| 型号： | ADP1046ACPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 24/92页 |
| 文件大小： | 0K |
| 描述： | IC DGTL CTRLR 32LFCSP |
| 标准包装： | 5,000 |
| 应用： | 电源 |
| 输入电压： | 0 V ~ 1.6 V |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 20mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-WQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
ADP1046
VDD
When VDD is applied, a certain time elapses before the part is
capable of regulating the power supply. When VDD rises above
the power-on reset and UVLO levels, it takes approximately
20 μs for VCORE to reach its operational point of 2.5 V. The
EEPROM contents are then downloaded to the registers. The
download takes an additional 25 μs (approximately). After the
EEPROM download, the ADP1046 is ready for operation.
If the ADP1046 is programmed to power up at this time (PSON
is enabled), the soft start ramp begins. Otherwise, the part waits
for the PSON signal.
The proper amount of decoupling capacitance must be placed
between VDD and AGND, as close as possible to the device to
minimize the trace length. It is recommended that the VCORE
pin not be used as a reference or to generate other logic levels
using resistive dividers.
VDD/VCORE OVLO
The ADP1046 has built-in overvoltage protection (OVP) on
its supply rails. When the VDD or VCORE voltage rises above
the OVLO threshold, the response can be programmed using
Register 0x0E[7:5]. It is recommended that when a VDD/
VCORE OVP fault occurs, the response be set to download the
EEPROM before restarting the part (set Register 0x0E[6] = 1).
Data Sheet
POWER GOOD
The ADP1046 has two open-drain power-good pins. The
PGOOD1 pin is driven low when a PGOOD1 fault condition
is present; the PGOOD2 pin is driven low when a PGOOD2
fault condition is present. The PGOOD1 and PGOOD2 pins
and flags can be programmed to respond to the following flags:
? Soft start
? CS1 fast OCP
? CS1 accurate OCP
? CS2 accurate OCP
? UVP
? Local OVP (fast and accurate)
? Load OVP
? OrFET (GATE pin)
The masking of these flags is programmed in Register 0x7B
(for PGOOD1) and Register 0x7C (for PGOOD2). When a flag
is masked, it does not set PGOOD1 or PGOOD2.
The following additional flags can also set the PGOOD2 pin either
unconditionally or based on the flag response, as programmed
? Voltage continuity
? OrFET disable
? ACSNS
?
?
External flag (FLAGIN pin)
OTP
These additional flags can be programmed in Register 0x2D[3]
to always set PGOOD2 or to set PGOOD2 only if the flag action
is not set to “ignore” in the fault configuration register for that
MAIN FLAGS
-SOFT START
-CS1 FAST OCP
MASKED BY
REG 0x7B
DEBOUNCE
(REG 0x2D[7:6])
PGOOD1
(FLAG AND PIN)
-CS1 ACCURATE OCP
-CS2 ACCURATE OCP
-UVP
-LOCAL OVP
(FAST AND ACCURATE)
-LOAD OVP
-OrFET (GATE PIN)
ADDITIONAL FLAGS
-VOLTAGE CONTINUITY
-OrFET DISABLE
-ACSNS
-FLAGIN
-OTP
MASKED BY
REG 0x7C
IF REG 0x2D[3] = 0, THE
ADDITIONAL FLAGS
ALWAYS AFFECT PGOOD2,
REGARDLESS OF THE
PROGRAMMED ACTION.
IF REG 0x2D[3] = 1, THE
ADDITIONAL FLAGS AFFECT
PGOOD2 ONLY IF THEY ARE
DEBOUNCE
(REG 0x2D[5:4])
PGOOD2
(FLAG AND PIN)
NOT SET TO BE IGNORED.
Figure 30. PGOOD1, PGOOD2 Programming
Rev. B | Page 24 of 92
相关PDF资料 |
PDF描述 |
|---|---|
| ADP1111ANZ-12 | IC REG BUCK BST INV 12V .2A 8DIP |
| ADP121-ACBZ12R7 | IC REG LDO 1.2V .15A 4WLCSP |
| ADP122AUJZ-2.9-R7 | IC REG LDO 2.9V .3A 5TSOT |
| ADP124ARHZ-2.85-R7 | IC REG LDO 2.85V .5A 8MSOP |
| ADP130AUJZ-2.5-R7 | IC REG LDO 2.5V .35A TSOT-23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1046ADC1-EVALZ | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ADP1046AWACPZ-R7 | 功能描述:Power Supply Controller Power Supplies 32-LFCSP-WQ (5x5) 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:有效 应用:电源 电压 - 输入:0 V ~ 1.6 V 电压 - 电源:3 V ~ 3.6 V 电流 - 电源:20mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP-WQ（5x5） 标准包装:1 |
| ADP1046DC1-EVALZ | 功能描述:BOARD EVAL DAUGHTERCARD ADP1046 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| ADP1047 | 制造商:AD 制造商全称:Analog Devices 功能描述:Digital Power Factor Correction Controller |
| ADP1047-300-EVALZ | 制造商:Analog Devices 功能描述:ANAADP1047-300-EVALZ 300W EVALUATION BOA 制造商:Analog Devices 功能描述:EVAL DIGITAL PFC CONTROLLER 300W 制造商:Analog Devices 功能描述:ADP1047, PFC CNTLR, 300W, EVAL KIT |
发布紧急采购，3分钟左右您将得到回复。