参数资料
| 型号： | ADP1046ACPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 35/92页 |
| 文件大小： | 0K |
| 描述： | IC DGTL CTRLR 32LFCSP |
| 标准包装： | 5,000 |
| 应用： | 电源 |
| 输入电压： | 0 V ~ 1.6 V |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 20mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-WQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
Data Sheet
Using the OTP Value
The second option does not use the linearization scheme.
Instead, the user programs an RTD current and sets the OTP
threshold in millivolts. Due to the nonlinear nature of the NTC
thermistor, it is best to use a resistor in parallel with the NTC
thermistor to aid in the linearization of the voltage seen at the
RTD pin.
This procedure trims out the errors/tolerances in the NTC therm-
istor and the external resistor. Calculation of the parallel resistor
can be done by knowing the NTC resistance characteristic across
various temperatures.
To use this procedure, the temperatures and equivalent resistances
of the NTC thermistor and parallel resistor combination must
be known.
In Figure 44, T2 is the OTP threshold that sets the OTP flag,
and T1 is the temperature at which the OTP flag is cleared.
ADP1046
The ADC is now trimmed and is linear between the two
temperatures of interest.
This procedure achieves the most accurate OTP because it takes
into account the part-to-part variations of the ADP1046 and the
tolerances of the thermistor being used.
ACSNS CALIBRATION AND TRIM
The ACSNS feedforward ADC (see Figure 18) is used for
voltage line feedforward and cannot be trimmed by the user.
The ACSNS slow ADC requires a gain trim. Enable the power
supply with full load current at the nominal input voltage. The
secondary peak reverse voltage on the output rectifiers is
To trim the ACSNS ADC, the user can reverse-calculate the
primary voltage as follows:
V PRIMARY = Vx × ( R1 + R2 )/ R2 × ( N1 / N2 )
T2 TEMPERATURE
RTD PIN
ADC CODE
V2
RTD PIN VOLTAGE
V1
V2
V1 T1
VOLTAGE
Figure 44. RTD Pin Voltage, ADC Code, and Temperature
where:
Vx is the voltage at the ACSNS pin.
N1 / N2 is the turns ratio.
The ACSNS gain trim register (Register 0x5E) is adjusted until
this calculated voltage is equal to the desired primary input
voltage.
Another way to trim the ACSNS ADC uses the average second-
ary voltage. With known values for the nominal input voltage,
transformer turns ratio, and resistor dividers at the ACSNS pin,
The following procedure should be used:
the ACSNS gain trim register (Register 0x5E) is adjusted to give
1.
2.
3.
4.
5.
6.
Adjust the desired RTD current source, I RTD , as described
in the Trimming the Current Source section.
Set the temperature to the OTP threshold.
Adjust the offset trim registers (Register 0x1C and Register
0x20) until the reading in Register 0x1A is the same as V2
(in mV).
Set the OTP threshold (Register 0x2F) to the value of V2.
Set the temperature to the hysteresis point where the OTP
flag is cleared.
Adjust the temperature gain trim register (Register 0x2B)
code 2560 decimal (0xA00).
ADC Code = Vx /1.6 × 4096
where Vx is the voltage at the ACSNS pin.
The resistors in Figure 18 are sized such that the first time
constant, RC, is long enough to prevent overcharging of the
capacitor (roughly 200 ns in a typical application), whereas the
second time constant, (R1 + R2) × C, is long enough to keep the
average voltage constant during the rectifier off time.
until the correct voltage is seen in Register 0x1A.
Rev. B | Page 35 of 92
相关PDF资料 |
PDF描述 |
|---|---|
| ADP1111ANZ-12 | IC REG BUCK BST INV 12V .2A 8DIP |
| ADP121-ACBZ12R7 | IC REG LDO 1.2V .15A 4WLCSP |
| ADP122AUJZ-2.9-R7 | IC REG LDO 2.9V .3A 5TSOT |
| ADP124ARHZ-2.85-R7 | IC REG LDO 2.85V .5A 8MSOP |
| ADP130AUJZ-2.5-R7 | IC REG LDO 2.5V .35A TSOT-23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1046ADC1-EVALZ | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ADP1046AWACPZ-R7 | 功能描述:Power Supply Controller Power Supplies 32-LFCSP-WQ (5x5) 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:有效 应用:电源 电压 - 输入:0 V ~ 1.6 V 电压 - 电源:3 V ~ 3.6 V 电流 - 电源:20mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP-WQ（5x5） 标准包装:1 |
| ADP1046DC1-EVALZ | 功能描述:BOARD EVAL DAUGHTERCARD ADP1046 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| ADP1047 | 制造商:AD 制造商全称:Analog Devices 功能描述:Digital Power Factor Correction Controller |
| ADP1047-300-EVALZ | 制造商:Analog Devices 功能描述:ANAADP1047-300-EVALZ 300W EVALUATION BOA 制造商:Analog Devices 功能描述:EVAL DIGITAL PFC CONTROLLER 300W 制造商:Analog Devices 功能描述:ADP1047, PFC CNTLR, 300W, EVAL KIT |
发布紧急采购，3分钟左右您将得到回复。