- 您现在的位置：买卖IC网 > PDF目录262949 > MT48V8M16LFB4-75M:G 8M X 16 SYNCHRONOUS DRAM, 5.4 ns, PBGA54 PDF资料下载
参数资料
| 型号： | MT48V8M16LFB4-75M:G |
| 元件分类： | DRAM |
| 英文描述： | 8M X 16 SYNCHRONOUS DRAM, 5.4 ns, PBGA54 |
| 封装： | 8 X 8 MM, LEAD FREE, VFBGA-54 |
| 文件页数： | 18/80页 |
| 文件大小： | 2775K |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
PDF: 09005aef807f4885/Source: 09005aef8071a76b
Micron Technology, Inc., reserves the right to change products or specifications without notice.
128Mbx16x32Mobile_2.fm - Rev. M 1/09 EN
25
2001 Micron Technology, Inc. All rights reserved.
128Mb: x16, x32 Mobile SDRAM
Register Definition
automatically performed upon completion of the READ or WRITE burst, except in the
full-page burst mode where auto precharge does not apply. Auto precharge is nonpersis-
tent in that it is either enabled or disabled for each individual read or write command.
Auto precharge ensures that the precharge is initiated at the earliest valid stage within a
burst. The user must not issue another command to the same bank until the precharge
time (tRP) is completed. This is determined as if an explicit PRECHARGE command was
issued at the earliest possible time, as described for each burst type in “Operation” on
BURST TERMINATE
The BURST TERMINATE command is used to truncate either fixed-length or full-page
bursts. The most recently registered READ or WRITE command prior to the BURST
TERMINATE command will be truncated, as shown in the Operation section of this data
sheet. The BURST TERMINATE command does not precharge the row; the row will
remain open until a PRECHARGE command is issued.
AUTO REFRESH
AUTO REFRESH is used during normal operation of the SDRAM and is analogous to
CAS#-BEFORE-RAS# (CBR) refresh in conventional DRAMs. This command is nonper-
sistent, so it must be issued each time a refresh is required. All active banks must be
PRECHARGED prior to issuing an AUTO REFRESH command. The AUTO REFRESH
command should not be issued until the minimum tRP has been met after the
PRECHARGE command as shown in the operation section.
The addressing is generated by the internal refresh controller. This makes the address
bits “Don’t Care” during an AUTO REFRESH command. Regardless of device width, the
128Mb SDRAM requires 4,096 AUTO REFRESH cycles every 64ms (commercial and
industrial) or 16ms (automotive). Providing a distributed AUTO REFRESH command
every 15.625s (commercial and industrial) or 3.906s (automotive) will meet the
refresh requirement and ensure that each row is refreshed. Alternatively, 4,096 AUTO
REFRESH commands can be issued in a burst at the minimum cycle rate (tRFC), once
every 64ms (commercial and industrial) or 16ms (automotive).
SELF REFRESH
The SELF REFRESH command can be used to retain data in the SDRAM, even if the rest
of the system is powered down. When in the self refresh mode, the SDRAM retains data
without external clocking. The SELF REFRESH command is initiated like an AUTO
REFRESH command except CKE is disabled (LOW). After the SELF REFRESH command
is registered, all the inputs to the SDRAM become “Don’t Care” with the exception of
CKE, which must remain LOW.
After self refresh mode is engaged, the SDRAM provides its own internal clocking,
causing it to perform its own auto refresh cycles. The SDRAM must remain in self refresh
mode for a minimum period equal to tRAS and may remain in self refresh mode for an
indefinite period beyond that.
The procedure for exiting self refresh requires a sequence of commands. First, CLK must
be stable (stable clock is defined as a signal cycling within timing constraints specified
for the clock pin) prior to CKE going back HIGH. After CKE is HIGH, the SDRAM must
have NOP commands issued (a minimum of 2 clocks, regardless of clock frequency) for
tXSR because time is required for the completion of any internal refresh in progress.
相关PDF资料 |
PDF描述 |
|---|---|
| MS8256FKXA-12 | 256K X 8 MULTI DEVICE SRAM MODULE, 120 ns, DMA32 |
| MT46V32M16BN-75IT | 32M X 16 DDR DRAM, 0.75 ns, PBGA60 |
| MT46V32M16P-6T | 32M X 16 DDR DRAM, 0.7 ns, PDSO66 |
| MT28F644W18FE-705KTET | 4M X 16 FLASH 1.8V PROM, 70 ns, PBGA56 |
| MPAT-122128-1003MS | 12200 MHz - 12750 MHz RF/MICROWAVE FIXED ATTENUATOR, 2.2 dB INSERTION LOSS-MAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MT48V8M16LFB4-8 ITG | 制造商:Micron Technology Inc 功能描述:DRAM Chip Mobile SDRAM 128M-Bit 8Mx16 2.5V 54-Pin VFBGA Tray |
发布紧急采购，3分钟左右您将得到回复。