- 您现在的位置：买卖IC网 > PDF目录296802 > PH28F128W18BD60A (INTEL CORP) 8M X 16 FLASH 1.8V PROM, 60 ns, PBGA56 PDF资料下载
参数资料
| 型号： | PH28F128W18BD60A |
| 厂商： | INTEL CORP |
| 元件分类： | PROM |
| 英文描述： | 8M X 16 FLASH 1.8V PROM, 60 ns, PBGA56 |
| 封装： | 9 X 11 MM, 1 MM HEIGHT, LEAD FREE, VFBGA-56 |
| 文件页数： | 64/106页 |
| 文件大小： | 1496K |
| 代理商： | PH28F128W18BD60A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页当前第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页
Intel
Wireless Flash Memory (W18)
07-Dec-2005
Intel Wireless Flash Memory (W18)
Datasheet
60
Order Number: 290701, Revision: 015
10.0
Read Operations
The device supports two read modes - asynchronous page and synchronous burst mode.
Asynchronous page mode is the default read mode after device power-up or a reset. The Read
Configuration Register (RCR) must be configured to enable synchronous burst reads of the flash
memory array (see Section 14.0, “Set Read Configuration Register” on page 84).
Each partition of the device can be in any of four read states: Read Array, Read Identifier, Read
Status or CFI Query. Upon power-up, or after a reset, all partitions of the device default to the Read
Array state. To change a partition’s read state, the appropriate read command must be written to the
device (see Section 9.2, “Device Commands” on page 55).
The following sections describe device read modes and read states in detail.
10.1
Asynchronous Page Read Mode
Following a device power-up or reset, asynchronous page mode is the default read mode and all
partitions are set to Read Array. However, to perform array reads after any other device operation
(e.g. write operation), the Read Array command must be issued in order to read from the flash
memory array.
Note:
Asynchronous page-mode reads can only be performed when Read Configuration Register bit
RCR[15] is set (see Section 14.0, “Set Read Configuration Register” on page 84).
To perform an asynchronous page mode read, an address is driven onto A[MAX:0], and CE#, OE#
and ADV# are asserted. WE# and RST# must be deasserted. WAIT is asserted during
asynchronous page mode. ADV# can be driven high to latch the address, or it must be held low
throughout the read cycle. CLK is not used for asynchronous page-mode reads, and is ignored. If
only asynchronous reads are to be performed, CLK should be tied to a valid VIH level, WAIT
signal can be floated and ADV# must be tied to ground. Array data is driven onto DQ[15:0] after
In asynchronous page mode, four data words are “sensed” simultaneously from the flash memory
array and loaded into an internal page buffer. The buffer word corresponding to the initial address
on A[MAX:0] is driven onto DQ[15:0] after the initial access delay. Address bits A[MAX:2] select
the 4-word page. Address bits A[1:0] determine which word of the 4-word page is output from the
data buffer at any given time.
10.2
Synchronous Burst Read Mode
To perform a synchronous burst- read, an initial address is driven onto A[MAX:0], and CE# and
OE# are asserted. WE# and RST# must be deasserted. ADV# is asserted, and then deasserted to
latch the address. Alternately, ADV# can remain asserted throughout the burst access, in which
case the address is latched on the next valid CLK edge after ADV# is asserted. See Section 14.0,
During synchronous array and non-array read modes, the first word is output from the data buffer
on the next valid CLK edge after the initial access latency delay (see Section 14.2, “First Access
Latency Count (RCR[13:11])” on page 86). Subsequent data is output on valid CLK edges
相关PDF资料 |
PDF描述 |
|---|---|
| PHC0683E1133-H | IC SOCKET |
| PHP12NQ15T | N-channel TrenchMOS transistor |
| PHB12NQ15T | N-channel TrenchMOS transistor |
| PHD12NQ15T | N-channel TrenchMOS transistor |
| PHP15N06E | PowerMOS transistor |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PH28F160C3BD70A | 制造商:Micron Technology Inc 功能描述:MM#865392FLASH 28F160C3BD 70 VF-PBGA46 C |
| PH28F256L18B85 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:StrataFlash Wireless Memory |
| PH28F256L18B85A | 制造商:Micron Technology Inc 功能描述:MM#875138FLASH 28F256L18B 85 VF-PBGA79 S |
| PH28F256L18T85 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:StrataFlash Wireless Memory |
| PH28F320C3TD70A | 制造商:Micron Technology Inc 功能描述:Flash Mem Parallel 3V/3.3V 32M-Bit 2M x 16 70ns 48-Pin VFBGA Tray 制造商:Micron Technology Inc 功能描述:MM#869664FLASH 28F320C3TD 70 VF-PBGA47 E |
发布紧急采购，3分钟左右您将得到回复。