- 您现在的位置：买卖IC网 > PDF目录98071 > S5933QE (APPLIEDMICRO INC) PCI BUS CONTROLLER, PQFP160 PDF资料下载
参数资料
| 型号： | S5933QE |
| 厂商： | APPLIEDMICRO INC |
| 元件分类： | 总线控制器 |
| 英文描述： | PCI BUS CONTROLLER, PQFP160 |
| 封装： | PLASTIC, QFP-160 |
| 文件页数： | 23/176页 |
| 文件大小： | 823K |
| 代理商： | S5933QE |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页
3-132
FIFO OVERVIEW
S5933
When the last location in the PCI to Add-On FIFO is
read by the Add-On, the FIFO pointer does not
change. If another read is performed before more
data enters the FIFO, the previous data is driven.
When a write to a full Add-On to PCI FIFO is at-
tempted, nothing happens. No FIFO data is overwrit-
ten and the FIFO pointers are not changed. This
behavior is the same whether the FIFO is accessed
using the direct access inputs or normal Operation
Register accesses.
Figure 8 shows a synchronous FIFO register burst
access. SELECT# must meet setup and hold times
relative to the rising edge of BPCLK. RD# and
SELECT# both asserted enables the DQ outputs, and
the first data location (data 0) in the FIFO is driven on
to the bus. The FIFO address and the byte enables
must be valid before valid data is driven onto the DQ
bus. Data 0 remains valid until the next rising edge of
BPCLK. The rising edge of BPCLK causes the FIFO
pointer to advance to the next location (data 1). The
next rising edge of BPCLK also advances the FIFO
pointer to the next location (data 2). The status outputs
reflect the FIFO condition after it advances, and are
updated off of the rising edge of BPCLK. When RD# or
SELECT# is deasserted, the DQ bus floats. The next
time a valid FIFO access occurs and RD# and SELECT#
are asserted, data 2 is presented on the DQ bus (as
there was no BPCLK edge to advance the FIFO).
Add-On FIFO Direct Access Mode
Instead of generating an address, byte enables, SELECT#
and a RD# or WR# strobe for every FIFO access, the
S5933 allows a simple, direct access mode. Using
RDFIFO# and WRFIFO# is functionally identical to per-
forming a standard AFIFO Port Register access, but re-
quires less logic to implement. Accesses to the FIFO
register using the direct access signals are always 32-
bits wide. The only exception to this is when the
MODE pin is configured for 16-bit operation. In this
situation, all accesses are 16-bits wide. The RD# and
WR# inputs must be inactive when RDFIFO# or
WRFIFO# is active. The ADR[6:2] and BE[3:0]# inputs
are ignored.
Depending on the device configuration, RDFIFO#
and WRFIFO# can act as clocks for data or enables
with BPCLK acting as the clock. A Synchronous in-
terface allows higher data rates, and an asynchro-
nous interface is better for slow Add-On logic which
may require wait states. The major difference be-
tween the synchronous and asynchronous modes is
when the FIFO advances.
Figure 9 shows an asynchronous FIFO register direct
access using RDFIFO#. The first location in the FIFO
is driven onto the bus when RDFIFO# is asserted.
Data remains valid as long as RDFIFO# is asserted.
The rising edge of RDFIFO# causes the data bus to
float and acts as the clock causing the FIFO pointer
to advance. The status outputs reflect the FIFO con-
dition after it advances.
Figure 10 shows a synchronous FIFO register direct
burst access using RDFIFO#. RDFIFO# acts as an
enable and the first data location (data 0) in the FIFO
is driven on to the bus when RDFIFO# is asserted.
Data 0 remains valid until the next rising edge of
BPCLK. The rising edge of BPCLK causes the FIFO
pointer to advance to the next location (data 1). The
next rising edge of BPCLK advances the FIFO
pointer to the next location (data 2). The status out-
puts reflect the FIFO condition after it advances, and
are updated off of the rising edge of BPCLK. When
RDFIFO# is deasserted, the DQ bus floats. The next
time RDFIFO# is asserted, data 2 is presented on the
DQ bus (as there was no BPCLK edge to advance
the FIFO).
A synchronous FIFO interface has the advantage of
allowing data to be accessed more quickly (in bursts)
by the Add-On. As a target, if a full S5933 FIFO is
Figure 8. Synchronous FIFO Register Burst Read Access Example
BE[3:0]#
BPCLK
ADR[6:2]
DQ[31:0]
SELECT#
RD#
RDEMPTY
Valid Byte Enables
FIFO Pointer Advances
Valid Address
Data 1
Data 2
Data 0
New Status
Status Before Read
相关PDF资料 |
PDF描述 |
|---|---|
| S6A0032 | 16 X 80 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC138 |
| S6A0069 | 16 X 40 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC80 |
| S6A0078 | 34 X 120 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC183 |
| S80296SA40 | 16-BIT, 40 MHz, MICROCONTROLLER, PQFP100 |
| S80486-DX4-75-S-V-8-B | 32-BIT, 75 MHz, MICROPROCESSOR, PQFP208 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S5935 | 制造商:AMCC 制造商全称:Applied Micro Circuits Corporation 功能描述:PCI Product |
| S5935_07 | 制造商:AMCC 制造商全称:Applied Micro Circuits Corporation 功能描述:PCI Product |
| S59355QRC | 制造商:AppliedMicro 功能描述: |
| S5935QF | 制造商:AMCC 制造商全称:Applied Micro Circuits Corporation 功能描述:PCI Product |
| S5935QRC | 制造商:AppliedMicro 功能描述:PCI Master Device 160-Pin PQFP |
发布紧急采购，3分钟左右您将得到回复。