参数资料
型号: M66596WG
元件分类: 总线控制器
英文描述: UNIVERSAL SERIAL BUS CONTROLLER, PBGA64
封装: 0.80 MM PITCH, FBGA-64
文件页数: 24/133页
文件大小: 1611K
代理商: M66596WG
M66596FP/WG
rev .1.00
2006.3.14
page 10 of 127
1.7 An overview of functions
1.7.1
The function selection
The controller can change a host function and a peripheral function by register setup.
When which of the Host function and the Peripheral function is chosen, hardware recognizes Hi-Speed or
Full-Speed automatically.
1.7.2
Bus interfaces
The controller supports the bus interfaces noted below.
1.7.2.1 External bus interface
The controller uses a CPU bus interface to access control registers.
The bus interface with the CPU supports the two access methods noted below. The Chip Select pin (CS_N) and
the three strobe pins (RD_N, WR0_N and WR1_N) should be used for access.
(1) (16-bit separate bus
The six address buses (A6-1) and the 16 data buses (D15-0) are used.
(2) 16-bit multiplex bus
The ALE pin (ALE) and the 16 data buses (D15-0) are used. The data buses are used for addresses and data on
a time-shared basis.
The separate bus and multiplex bus are selected based on the MPBUS pin signal level when the H/W reset is
canceled.
1.7.2.2 Accessing the buffer memory
The controller supports the two methods described below to access the USB data transfer buffer memory.
(1) CPU access
Addresses and control signals should be used to write data to the buffer memory or read it from the buffer
memory.
(2) DMA access
Data should be written to the buffer memory of the controller, or read from the buffer memory, from the
DMAC in the CPU or a dedicated DMAC.
USB data communication is done using Little Endian. There is a byte Endian swap function for FIFO port
access, and when using 16-bit access, the Endian can be switched using the register settings.
1.7.2.3 DMA access methods
When using DMA access to access the buffer memory, the two access methods noted below can be selected.
(1) Method using a bus shared with the CPU
(2) Method using a dedicated bus (split bus)
1.7.3
USB events
The controller notifies the user’s system of USB operation events by means of interrupts. Moreover, with a pipe
for which the DMA interface has been selected, the system is notified that the buffer memory of the controller
can be accessed by asserting the DREQ signal.
There are 12 types of interrupts and 39 causes for interrupts being generated. The user can select whether or
not interrupt notification is permitted for each type and each cause, using settings in the control program for the
user system.
相关PDF资料
PDF描述
M6XXLFXI OTHER CLOCK GENERATOR, QCC16
M300LFXIT 50 MHz, OTHER CLOCK GENERATOR, QCC16
M74HC00C1R HC/UH SERIES, QUAD 2-INPUT NAND GATE, PQCC20
M74HC157B1N HC/UH SERIES, QUAD 2 LINE TO 1 LINE MULTIPLEXER, TRUE OUTPUT, PDIP16
M74HC158C1 HC/UH SERIES, QUAD 2 LINE TO 1 LINE MULTIPLEXER, INVERTED OUTPUT, PQCC20
相关代理商/技术参数
参数描述
M66596WG#RB0Z 制造商:Renesas Electronics 功能描述:Tray 制造商:Renesas 功能描述:0
M6668 制造商:Tamura Corporation of America 功能描述:
M66700P 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:DUAL HIGH-SPEED CCD CLOCK DRIVER
M66700WP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:DUAL HIGH-SPEED CCD CLOCK DRIVER
M66701P 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:DUAL HIGH-SPEED CCD CLOCK DRIVER